Timing belt on rapid when to change. Engine resource estimation on Skoda Rapid

According to the manufacturer, the timing chain does not change at all, since it is designed for the entire life of the engine. It is also not possible to tighten the chain manually, since there is a hydraulic tensioner there.

In the event of a malfunction, it is urgent to visit an authorized Skoda service center to diagnose or replace the timing chain.

The consequences of failure of the timing chain

In engines, perhaps, the gas distribution mechanism attracts the closest attention, if you do not take into account the replacement of oil and oil filter.

After all, broken toothed belt The timing can do a lot of trouble, somehow bent valves and connecting rods, which translates into a very expensive repair. Therefore, timely replacement of the belt, as well as engine oil, is the key to a long engine life.

It seems that Volkswagen engineers were guided by these factors when they began to install a chain instead of a belt on many of their engines. Moreover, on most engines, the chain is designed for the entire period of operation.

It would seem an excellent solution, but many motorists have a completely opposite opinion, after more than one engine has failed due to chain stretching.

And it happened on small runs, 60-70 thousand kilometers. Also, a failed hydraulic chain tensioner can contribute to engine breakdown.

maintenance regulations Skoda Rapid in PDF formatTimely diagnosis

In general, do not be lazy and with a run of 60 thousand for maintenance, ask to remove the timing cover and check how far the chain tensioner has advanced, if it has advanced more than four marks, this is a signal to replace the chain.

The Rapid also has engines with a timing chain. Particularly close attention requires 1.2 liter engine turbocharged.

How reliable are they, has anyone asked this question? And are these engine data still relevant or are there modernized engines on Rapid?

The timing belt is the link between the camshaft and crankshaft. Serves to synchronize the following elements - pistons and valves. Thanks to this consumable, the efficiency of the engine is ensured internal combustion. But, like any other consumable part, the timing belt has an approximate period of use, at the end of which the element must be replaced.

When is replacement required?

The timing belt on the Skoda Rapid must be changed every 50-70 thousand kilometers. But it all depends on the area in which the car is operated. For example, in Russian latitudes in summer the air temperature can reach up to +40 degrees Celsius, and in winter up to -50 degrees Celsius. Such temperature differences seriously affect the parts installed in the vehicle.

The following are symptoms in which you need to immediately evaluate the condition of the timing belt.

The main signs of the need to replace the belt:

• Duration of operation of the belt element. It is required to immediately check its condition and, if necessary, replace it;
• Difficult start of the power unit, which is accompanied by a loss of power;
• The appearance of smoke (black) from the exhaust pipe;
• Strange sounds that appeared in the engine compartment;
• The presence of traces of coolant and oil on the surface of the part;
• Scuffs and cracks on the belt;
• The power unit stopped starting, despite the effective operation of the starter.

One of the symptoms described above may indicate a malfunction of the timing belt. It needs to be checked as soon as possible. If he is really in a deplorable state, you need to take care of independent procedure replacements. But in order to carry out this process, you must first choose the right part.

Choosing a new belt

Auto shops offer a wide range of parts for different models of cars. It is enough to choose the right belt size with the required number of teeth and find the name of your car in the list of recommended models. It is advisable to buy spare parts from well-known manufacturers.

Famous manufacturers who make timing belts:

• gates;
• contitech;
• Bosch;
• Dayco.

Some of them have entered into contracts with well-known car manufacturers for the supply of spare parts. This means that their quality is top notch. After acquiring a suitable belt, you can begin preparatory work for the independent replacement of the timing element.

Step-by-step instructions for self-replacing the timing belt on the Skoda Rapid 1.6

Necessary tools and materials for replacing the timing belt on the Skoda Rapid 1.6:

• Sets of keys (heads, open-end, hexagons);
• Screwdrivers (phillips and regular);
• A hammer;
• Chisel;
• Fasteners;
• New belt;
• Clean rags;
• Cloth gloves (if necessary).

Also, do not forget about the rules of technical safety.

Important safety precautions when replacing consumables:

1. The vehicle must be parked on a level surface. You can use a covered room (garage or other building). Downpour, strong wind should not interfere with the process.
2. It is advisable to use a viewing hole, overpass or lift. Much work will be carried out at the bottom vehicle. Such facilities will create maximum comfort.
3. Apply the parking brake and install the wheel chocks.
4. Set the gear lever to neutral position.
5. Disconnect the negative battery terminal.

After implementation preparatory work, you can proceed directly to the replacement. Namely, to remove the timing belt.

Removing the belt

Step-by-step instructions for removing the belt on the Skoda Rapid:

Installation

Timing belt installation on Skoda Rapid 1.6:

The replacement of the timing belt on the Skoda Rapid is completed. The duration of the procedure is about 5-7 hours. It all depends on the availability of the necessary parts, special tools and skill.

High-quality repair and diagnostics of cars and commercial transport. We work with individuals and organizations. We carry out diagnostics of the brake system and running gear, engine repair, car maintenance, bodywork and painting. Auto electricians with many years of experience work in the state. Motorists specialize in certain brands of cars.

Car service on Piskarevka - Energetikov avenue, house 59.

Located next to the metro station "Ploshchad Lenina". Covers car repairs in Kalininsky, Vyborgsky and Primorsky districts of St. Petersburg. Performs all work on the chassis, engine, suspension and installation of additional equipment. A new wheel alignment stand for cars and minibuses has been installed. Doesn't do car painting or body work. It is convenient to get from the metro stations "Ozerki", "Prospect of Enlightenment", "Specific" and "Pionerskaya". There is a cozy cafe in the building. To the ring road - 10 minutes.

Car service in Kupchino - st. Dimitrova, house 1

Initially, the service was only body repair and painting. Subsequently, several buildings were built in which new two and four post lifts were installed. Large car wash for cars and commercial vehicles. Separate workshop for diagnostics of diesel and petrol injectors. Steering racks, turbines and auto electrics are being repaired. The repair of mechanical and automatic boxes. Within walking distance from the metro station "Zvezdnaya", "Kupchino", "Obukhovo". Suitable for residents of the Frunzensky and Kirovsky districts.

FUNCTIONAL PURPOSE OF THE TIMING BELT

Replacing the timing belt is part of the scheduled Maintenance Skoda car Rapid and plays important role in the operation of the vehicle engine. Untimely replacement belt can lead to a malfunction of the motor, and a break to deformation of the valve timing mechanism and the need for overhaul engine.

All parts of the gas distribution mechanism are closely related to each other, injection air-fuel mixture drives the piston of the engine cylinder, which in turn pushes the crankshaft connected by a drive belt with camshaft. Thus, there is a movement of the camshaft, which regulates the frequency of movement of the valves. The Skoda Rapid timing belt connects gears and transmits torque from crankshaft to the distribution one, affecting the speed of its rotation. If the system is working, the frequency of their revolutions should be equal.

TYPES OF FAULTS OF THE TIMING BELT

1. Timing belt wear leads to a change in the torque transmission force from the crankshaft to the camshaft, resulting in a change in the frequency of movement of the pistons and engine valves. This, in turn, leads to a malfunction of the gas distribution system, rapid heating of the engine and, as a result, a decrease in engine power and an increase in the consumption of the fuel mixture. For reliable and uninterrupted operation of the motor, it is necessary that the valves close and open at the same frequency as the engine pistons. If, due to wear, the timing belt slips, this can cause a break.
2. Breakage of the timing belt Skoda Rapid - is the most dangerous damage to the engine. In the event of such a malfunction, the camshaft ceases to be connected to the crankshaft and can stop completely arbitrarily in a position in which any of the valves of the gas distribution mechanism is open. In this case, the piston, moving up, may collide with the valve, which will lead to its deformation. In this case, the car's engine is in danger of serious repairs. It should be noted that a timing belt break does not occur unexpectedly, it is almost always accompanied by changes in the operation of the car engine, a decrease in its power, a change in gasoline consumption, the appearance of extraneous squeaks, squeaks, etc.

To prevent and prevent the operation of the gas distribution mechanism, it is necessary to periodically replace the timing belt, this will save the Skoda Rapid car engine from breakdown, prevent premature engine wear and increase its service life.

CAUSES AND ASSESSMENT OF WEAR OF THE TIMING BELT

Timing belt wear occurs for a number of reasons, avoiding which can extend the life of a car engine.

To prevent complete wear of the timing belt, it is necessary periodically, during a visual inspection of the gas distribution mechanism, to check for damage on the surface of the belt. To inspect and evaluate the belt drive, it is necessary to unscrew and remove the protective cover of the mechanism, under which the engine is hidden. The first signs of wear are:

• the appearance of oil and antifreeze smudges that can chemically destroy the timing belt, with prolonged exposure;
• the occurrence of longitudinal cracks on the back surface of the belt;
• the formation of transverse cracks on the inner surface of the drive belt;
• a ragged surface and a violation of the integrity of the edge are also a sign of wear;
• belt wear is also indicated by rubber dust on the surface of the part;
• if the timing belt teeth begin to peel off or wear out, the part must be replaced immediately with a new one.

SYMPTOMS OF A FAULTY TIMING BELT

1. Increased consumption of gasoline by car
2. Decreased engine power
3. Full stop of the car on the go, when you try to start the engine does not start, and the starter rotates easier than usual
4. Unstable operation of the engine Idling and in motion;
5. The occurrence of shots in the injector receiver and exhaust pipe

All these problems may indicate a shift in the valve timing and loosening of the belt tension. If you notice one or more signs of this list on your Skoda Rapid, immediately contact the service station for an inspection.

HOW OFTEN SHOULD YOU REPLACE A Skoda Rapid Timing Belt?

The frequency of replacement of any consumables for cars depends on the style of driving and the mode of operation of the car. With extreme driving style and aggressive use of the vehicle, it is necessary to replace the timing belt as it wears out and the teeth wear out.

AT normal conditions operation, it is necessary to replace the original timing belt as planned, every 60 - 70,000 km. run. During this period, it develops its resource and becomes unusable. If an analog belt is installed on your Skoda Rapid, the replacement must be done a little earlier than the period recommended by the vehicle manufacturer.

WHICH TIMING BELT IS BETTER TO CHOOSE

Modern belts for the gas distribution system are a high-tech product, characterized by increased strength and wear resistance, capable of withstanding high dynamic loads. Timing belts are produced from neoprene or polychloroprene reinforced with strong fiberglass, nylon and cotton cords.

1. To avoid the mistake associated with buying a timing belt, contact the specialists who will help you order a timing belt suitable for your car engine using the WIN code of your car. This part is one of the most important in the design of the motor, the slightest deviation in the length, width, shape and size of the teeth can lead to malfunctions in the engine of the Skoda Rapid.
2. Do not try to save money when buying a timing belt, a cheap product can be a low-quality fake that will quickly become unusable and can cause serious engine damage in the future. The best option for any car, there are original parts, their cost is higher than analog ones, but during the operation of the car they quickly pay for themselves.
3. When buying a timing belt, check it for stiffness, good belt should be elastic and easy to bend. The worse the belt, the more rigid it will be.
4. The presence of teeth, sagging, pores on the belt is not allowed - these are signs of a poor-quality belt that will quickly become unusable. The surface of the product must be smooth, small burrs are allowed.
5. When buying on your own, check the timing belt part number printed on the back, it must match the WIN code of the car. If it is not possible to compare the code of the belt and the car, then it is necessary to make a visual comparison of the old and new belts, they must be completely identical.
6. To avoid buying a fake, try to purchase spare parts only from authorized, trusted dealers.
7. Do not save on a qualified timing belt replacement, contact our certified car service, where competent mechanics will help with the repair of a Skoda Rapid car. And in the spare parts store you can buy original spare parts for your car.

The Skoda Rapid golf class liftback was presented in 2012. Sales of the model in most countries of the world began after twelve months. Rapid reached Russia only in 2014 in a modernized form. The manufacturer slightly increased the ground clearance, improved the suspension and adapted it to our roads.

Despite the fact that very few years have passed since the start of car production, today the Skoda Rapid boasts solid popularity. And all because the manufacturer managed to design a car that was successful in every sense, which filled the gap between and Fabia. Before purchasing a liftback, it is best to familiarize yourself with the engine resource on this vehicle.

Power plant options

Initially, anyone could purchase a Skoda Rapid with one of the three available engines with a displacement of 1.2 to 1.6 liters. The three-cylinder 1.2-liter engine was frankly weak, and did not allow the owner of the liftback to fully experience the whole drive and enjoy driving. The motor has often been criticized by independent experts, it is worth saying that it is quite reasonable. Ultimately, the Czechs decided to abandon the further completion of their offspring with this engine modification.

Thus, since 2015, the following installation options have remained available:

• Atmospheric 1.4-liter engine paired with five-speed mechanics;
• Atmospheric 1.6-liter engine paired with a 5/6-speed manual/automatic;
• Turbocharged 1.4-liter engine with a 7-speed robotic box.

As for the choice of boost degree, here, who wants to get a modern liftback, there is a small choice: 90, 110 and 125 Horse power respectively. However, the manufacturer has done a lot of work lately. The Czechs are constantly working on Skoda Rapid engines, improving them technically. Most recently, all three developments have received updated fuel injection technology, and the design, which predetermines not three, but four cylinders, helps to reduce fuel consumption and increase the dynamic performance of the car.

Engine resource 1.4 TSI

1.4 TSI atmospheric engine paired with mechanical box is by far the most requested modification. The turbocharged version can rightfully be called the top assembly. Four-cylinder power unit functions due to the timing chain, which has a good service life. The manufacturer recommends replacing it after a run of 70-80 thousand kilometers. Despite the fact that the timing chain was initially positioned as a “perpetual mechanism”, practice has shown that sometimes it fails even before the allotted time. Therefore, it is recommended to replace it earlier if the vehicle is operated in difficult conditions.

The manufacturer claims that the Skoda Rapid with a 1.4-liter engine under the hood will cover at least 250-300 thousand kilometers. There are good reasons to trust this information. The fact is that this power unit showed impressive reliability even with the time it was completed for Volkswagen cars. The new E211 units, which replaced the EA111 series motors, are distinguished by a cast-iron block, an aluminum head, lightweight pistons and a reinforced crankshaft. Improved specifications allow Skoda owner Rapid count on trouble-free operation of the car up to the first 300 thousand kilometers.

Motor resource 1.6 MPI

The engine block is made of aluminum, but the cylinder liners are cast iron. Such a design is not the cheapest, but from an engineering point of view it is reliable. After all, cast iron is distinguished by its heat-conducting properties, combined with high wear resistance. Heat transfer becomes even more efficient due to the rough surface of the sleeve walls. The 1.6-liter engine has found improved, lightweight pistons. The "flat" shape of this part makes the motor more powerful and dynamic. This is a technological novelty, because earlier designers could not achieve optimal combustion of the fuel mixture in the chamber due to the flat bottom of the part.

There is also a chain that is more reliable than a belt, but requires a lot of time and money during replacement. Model with a 1.6-liter engine - perfect option for daily travel. In addition, this version of Skoda Rapid is convenient to go on long journeys. Due to the design improved compared to the 1.4 TSI modification, the 1.6 MPI assembly is also distinguished by a longer resource - about 350-400 thousand kilometers. It is not uncommon for Skoda Rapid to pass half a million kilometers of road.

How long does the Skoda Rapid engine run according to car owners reviews

About what it really is real consumption of the Skoda Rapid engine, the reviews of the owners, who, from their own experience, were convinced of the high duration of stable operation of the main unit, will be more informative.

1.4TSI

1. Pavel, Moscow. I am a former owner of Skoda Rapid 1.4L. It just so happened that recently had to say goodbye to the car. Overall, she left behind good impressions- a convenient and practical body, low fuel consumption, and, of course, a great resource. It is not difficult to find a component, and much is suitable from VG cars. Personally, I drove about 80 thousand km by car during all this time, I did not notice any problems and “jambs” of the assembly. There are also no complaints about the chassis, it cheerfully holds the road.
2. Alexey, Saratov. I don’t drive too much, in four years I clocked 120 thousand kilometers. I replaced the chain, the process is laborious, but it's worth it. Moreover, he replaced it at the turn of the first hundred thousand, although the car did not give any signals. The 1.4 engine is peppy and assertive, this volume and power is enough for a comfortable daily movement around the city. Maintenance is inexpensive, as are parts. I expect to drive a car to the capital at least 250 thousand km.
3. Mikhail, Rostov. Acquired new car in 2012. For the first time using the machine, I noticed how the pistons were knocking. I went to the service center, they quickly fixed everything. The Czechs have known about this for a long time, allegedly, the problem was solved back in 2013. How things are with the pistons on the new assemblies, I don’t know. Today, the mileage is 180 thousand kilometers. During this time, I changed the timing chain once, which is much more reliable than the belt. Replaced once - another hundred thousand kilometers can be driven. I use imported engine oil. If you use certified fuel and lubricants, the engine will pass 300 thousand km without problems.
4. Kirill. Moscow. Great machine, no complaints. Definitely worth your money. I do not recommend spoiling the firmware, it may affect the overall resource of the Skoda Rapid engine. "Eats" a little, maintenance and accessories are inexpensive. For three years, I have already clocked up 90 thousand kilometers. Chassis excellent clearance for our roads. The build quality is no worse than many models from VG, and somewhere even better.

Owners of the Skoda Rapid 1.4 TSI note the high performance properties of the modification, reliability and long engine life. The chain resource is 90-100 thousand kilometers, which is more than the period declared by the manufacturer. This car is able to pass 200-250 thousand km without any problems.

1.6 MPI

1. Vasily, St. Petersburg. From my own experience I can say that the resource of the engine depends on 30% of the quality of fuel and lubricants, and 70% on the driving style. I stick to a calm manner, so my Rapid after four years of operation has never seriously broken down. Like everyone else, I went through scheduled maintenance, changed consumables and the timing chain. It is also important to refuel with good fuel, fill in imported oil and be serviced only at the OD.
2. Sergei, Voronezh. I will say this - I am dissatisfied with the car. Upon reaching the mark of 150 thousand kilometers, literally everything began to break down. The new pistons are clearly underdeveloped, we had to spend a lot of money on replacing parts of the piston group. Used Skoda Rapid for five whole years, and just recently sold the car. In return, I got damaged nerves, sleepless nights and a bunch of money thrown out of the wind.
3. Albert, Vladivostok. Initially thought to purchase a version with a turbocharged engine, but at the last moment changed his mind. I bought a Skoda Rapid 1.6 L 2013 with a manual transmission. I like the car for everyone: from assembly to design. One friend works as a taxi driver on a turbocharged Rapid, his mileage has already exceeded 300 thousand, however, the turbine needs additional care. So far, I have a mark of 120 thousand km.
4. Vladislav, Khabarovsk. I have a 2017 car with an upgraded 1.6-liter engine. I don’t know, I got an unsuccessful assembly, or the Czechs simply forgot how to assemble cars. The reliability of the new aspirated has clearly fallen, the reason for this is the new pistons! The timing belt is now quieter, but it is unsuitable for repair, plus every time I mark “zhor” with the engine oil. I am not sure that this unit will exhaust at least the resource put into it, not to mention the development in excess of the norm.

Skoda Rapid 1.6 received different ratings from drivers. Mostly owners of cars manufactured in 2013-2014 speak positively about the car. Owners new version So far, some design flaws have been noted, which the manufacturer may eliminate in the future. In general, this version of the car passes 250-300 thousand kilometers without problems and breakdowns.