What oil is best for a bmw engine. The right choice of oil for BMW

According to the instructions for maintenance of BMW E39, an oil change must be carried out either once a year or after a run of 15 thousand kilometers for gasoline engines and every 10 thousand for a diesel engine. Such recommendations are valid there, abroad. There is a small note in the manual: if the car is operated in difficult conditions, then the engine oil must be changed twice as often. That is, for gasoline power units every 7-8 thousand, and for diesel - every 5000. When driving on our fuel and on our roads, we can say with confidence that a car in the post-Soviet expanses is operated in heavy road conditions. So, when it is necessary to change the oil in the BMW E39 engine, we figured it out, now we will try to understand what and where to fill in.

What oil to fill in E39?

As you know, motor oils are mainly classified by base and viscosity. It can be divided by the type of base: mineral and synthetic. There is semi-synthetic oils. Viscosity is regulated by various additives and chemical additives. If you rummage through the Internet and read posts on various forums, then you will get a complete mess in your head. Some advise only synthetic, others semi-synthetics, others insist only on mineral oil, especially if the car has more than 100 thousand mileage. And the discussions and recommendations of various manufacturers in general can lead to a dead end the whole thought process.

Let's figure it out. mineral oils for engines bmw is better do not use. After all, the task of oil is not only to lubricate parts power unit, but also in cooling, corrosion prevention, removal of wear products. "Mineralka" quickly loses its characteristics, therefore it is not able to protect the motor as much as possible and ensure it normal work. Mineral-based oils are cheaper, and this is the main argument of many car owners. But if you want your car to serve for a long time and properly, fill in synthetic and semi-synthetic oils. The presence of special additives in them will extend the life of the motor.

To make your choice easier, below is a table of engine oil viscosities from the instruction manual pages. BMW operation. The main criterion for choosing will be the climate in which the car is operated.

The main criterion for choosing oil is the climate in which the car is operated.

It is logical to fill the engine with the oil recommended by the car manufacturer. But such recommendations are not always specific. The main thing is that the oil meets the ACEA class: A3 / B3 (CCMC-G5 / PD2) or API SJ / CD. There are a lot of manufacturers on this list. It is called Special oils and is updated every year. These are engine oils recommended by BMW AG. After examining the list, we can conclude that oil from well-known brands is suitable for the BMW E39. It is important that the oil was produced at the manufacturer, and not spilled in the basement of a neighboring house. Buy oil only from trusted dealers of official brands.

The main thing is that the oil meets the ACEA class: A3 / B3 (CCMC-G5 / PD2) or API SJ / CD

If you do not trust anyone, then you can order the original oil from BMW. Its original code is 83 21 9 407 782. This is the code for a liter canister. For complete replacement engine oil needs 6.5–7.5 liters. (depending on the engine).

Do-it-yourself engine oil change in E39

To change the engine oil, you will need the following tools and materials:

1. Rags to clean up spilled oil.
2. Low capacity for used oil, volume about 8 liters.
3. A set of ring or socket wrenches.
4. Narrow slotted screwdriver.
5. Phillips screwdriver.
6. Sharpened knife.
7. Oil filter kit: filter element, oil seal ring under the housing cover, copper washer for sealing drain plug. original number: 11 42 7 512 300.

Oil filter kit

The kit does not include 2 oil filter housing cover rod seals. It is advisable to order them separately and replace them. Part number 11 42 1 744 001.

1. Engine oil approved by BMW LL-98 or LL-01, such as Valvoline Syn Power SAE 5W-50 or Valvoline Top Gard SAE 10W-40.

You can use a filter from another manufacturer. For example, the cross-code of the filter for BMW E39 according to the MANN-FILTER catalog: HU 925/4X.

The procedure for performing work on changing the oil

It is better to change the oil in a pit or overpass. The oil filter is located in a special housing between the radiator and the engine. The motor should not be cold, however, when using synthetic oils, this requirement is not important. "Synthetics" retains good fluidity even at +10 degrees Celsius.

The oil filter is located in a special housing between the radiator and the engine.

1. We unscrew the cover of the filter housing using the socket head. Remove it and disconnect the filter element from it.
2. We remove the old seals from the cover rod by cutting them off with a knife.
3. We install new o-rings, after lubricating the rod with new oil.
4. Wipe the oil filter housing with a prepared rag.
5. We install a new filter element in the housing.
6. We fasten the cover, carefully tighten it with a wrench.
7. Open the neck on the engine to fill the oil.
8. If protection is set engine compartment from below, then open the mudguard with a Phillips screwdriver. We discard it.
9. Loosen the drain plug on the engine block.

Loosen the drain plug on the engine block

1. We substitute the prepared container and unscrew the cork completely. Drain the used oil.
2. We replace the sealing washer on the plug and screw it back into the engine block. Tighten with a key.
3. Pour about six liters of new engine oil through the oil filler neck. We close the neck.
4. We measure the oil level with a dipstick. It should be at the MAX mark or even slightly higher.
5. We start the engine and observe the emergency oil pressure indicator. It should light up and go out after a few seconds. If the indicator does not go out, then turn off the engine and start it again after 10-15 seconds. The indicator should turn off. After letting the engine run for a few minutes, turn it off.
6. After 15-20 minutes, check the oil level. If necessary, add it to the maximum mark.

Oil change video

1. The manufacturer does not recommend flushing the engine when changing the oil. If you use high-quality motor oil, then flushing the motor is not necessary. It is recommended to use flushing only when switching from mineral water to semi-synthetic or synthetic oils.
2. Do not change the brand of engine oil or add oil from another brand. Different manufacturers use different additives that can "quarrel". As a result, you can fly into a large sum when repairing the power unit.

What you need to know when choosing oil for BMW engines? Which oil is suitable for a particular engine? These are the two questions that matter the most. BMW owners undecided on the choice of oil when its scheduled replacement is approaching. First of all, it should be remembered that engine oils for BMW are divided into certified(admitted) and special(Special Oil). Moreover, according to the specifications of the automaker, for gasoline modifications of the BMW 1,3,4,5,6,7 series, it is allowed to use only those engine oils that have passed special tests and have been officially approved by BMW. For diesel versions the same models, the use of universal motor oils is allowed, subject to their compliance with the requirements of the documentation for each car model (according to ACEA classifications). For BMW approved engine oil, the appropriate approval must be indicated on the packaging. Its absence indicates the absence of BMW certification, therefore its use is not recommended.

Oils certified by BMW received the name longlife. These oils meet ACEA:A3/B3 specification standards and have been tested by BMW for their ability to provide extended service intervals. Maintenance(oil service). The use of these oils is allowed both in summer and in winter.

Since 2001, BMW began to produce engines of a new generation, which entailed tougher requirements for oil properties. As a result, oils with a long service life were divided into four categories:

   1. Longlife-01- oils that meet the full list of BMW requirements for technical liquids and recommended for use in N62/N42 engines. In addition, these oils are recommended for use in older BMW engines (manufactured before February 2000), except for S62 (e39), CNG, M43.

   2. Longlife-01FE (Fuel Economy)- oils with the same standards as Longlife-01, but with a lower viscosity, resulting in reduced fuel consumption. The use of these oils is allowed only in those engines, design features which allow the use of low viscosity oils.

   3. Longlife-98(original name - Longlife) - oils that meet the standards with an extended maintenance interval (OilService), introduced in 1998. The use of these oils is recommended for BMW engines equipped with forced ignition (except for S54, N42, and S62 (e39) produced before February 2000).

   4. Longlife-04- this tolerance has been introduced for engine oils that have passed a hollow test cycle at BMW. Oils with this approval can be used in modern motors BMW and is not recommended for cars manufactured before 2004.

Category special oils (Special Oil) as well as certified, it complies with ACEA: A3 / B3 specification standards and is an earlier version of BMW Longlife category oils. The use of special oils is recommended for older BMW models with a change interval of up to 15,000 kilometers (according to the OilService regulations). Special oils are multigrade. The exception is oils with a viscosity grade SAE 10W-X - its use is allowed at an ambient temperature of at least 20 ° C.

It should be remembered that for BMW engines it is recommended to use only engine oils that meet the above recommendations. The presence in the name of oils of such formulations as “fully synthetic (light-flowing) motor oil”, etc., is not evidence of the possibility of their use in BMW engines and can only be considered as a general name. The decisive factor in determining the suitability of the oil can only be an indication of the approval from BMW.

In conclusion, a few words about oils for new cars and engines after overhaul. And if hardly anyone will produce self-replacement oils outside the official service in new cars, then for BMW owners with engines after the “capital” it does not hurt to know that in BMW engines so-called "break-in" oils are not used. Therefore, when changing oil in engines after a major overhaul (as well as for new engines), it is recommended to use only the above-mentioned certified oils.

What you need to know when choosing oil for BMW engines? Which oil is suitable for a particular engine? It is these two questions that most concern BMW owners who have not decided on the choice of oil when its scheduled replacement is approaching. First of all, it should be remembered that engine oils for BMW are divided into certified(admitted) and special(Special Oil). Moreover, according to the specifications of the automaker, for gasoline modifications of the BMW 1,3,4,5,6,7 series, it is allowed to use only those engine oils that have passed special tests and have been officially approved by BMW. For diesel versions of the same models, the use of universal motor oils is allowed, provided that they comply with the requirements of the documentation for each car model (according to ACEA classification). For BMW approved engine oil, the appropriate approval must be indicated on the packaging. Its absence indicates the absence of BMW certification, therefore its use is not recommended.

Oils certified by BMW received the name longlife. These oils meet ACEA:A3/B3 specification standards and have been tested by BMW for their ability to provide extended service intervals (OilService). The use of these oils is allowed both in summer and in winter.

Since 2001, BMW began to produce engines of a new generation, which entailed tougher requirements for oil properties. As a result, oils with a long service life were divided into four categories:

   1. Longlife-01- oils that meet the full list of BMW requirements for technical fluids and are recommended for use in N62 / N42 engines. In addition, these oils are recommended for use in older BMW engines (manufactured before February 2000), except for S62 (e39), CNG, M43.

   2. Longlife-01FE (Fuel Economy)- oils with the same standards as Longlife-01, but with a lower viscosity, resulting in reduced fuel consumption. The use of these oils is allowed only in those engines, the design features of which allow the use of oil with a low viscosity.

   3. Longlife-98(original name - Longlife) - oils that meet the standards with an extended maintenance interval (OilService), introduced in 1998. The use of these oils is recommended for BMW engines equipped with forced ignition (except for S54, N42, and S62 (e39) produced before February 2000).

   4. Longlife-04- this tolerance has been introduced for engine oils that have passed a hollow test cycle at BMW. Oils with this approval can be used in modern BMW engines and is not recommended for vehicles manufactured before 2004.

Category special oils (Special Oil) as well as certified, it complies with ACEA: A3 / B3 specification standards and is an earlier version of BMW Longlife category oils. The use of special oils is recommended for older BMW models with a change interval of up to 15,000 kilometers (according to the OilService regulations). Special oils are multigrade. The exception is oils with a viscosity grade SAE 10W-X - its use is allowed at an ambient temperature of at least 20 ° C.

It should be remembered that for BMW engines it is recommended to use only engine oils that meet the above recommendations. The presence in the name of oils of such formulations as “fully synthetic (light-flowing) motor oil”, etc., is not evidence of the possibility of their use in BMW engines and can only be considered as a general name. The decisive factor in determining the suitability of the oil can only be an indication of the approval from BMW.

In conclusion, a few words about oils for new cars and engines after a major overhaul. And if it is unlikely that anyone will make an independent oil change outside the official service in new cars, then for BMW owners with engines after the “capital” it does not hurt to know that so-called “break-in” oils are not used in BMW engines. Therefore, when changing oil in engines after a major overhaul (as well as for new engines), it is recommended to use only the above-mentioned certified oils.

Very often there are questions about which oil to pour into bmw engine. What to pour and how to pour. On the forums, the branches with the choice of oil are quite large, there are huge disputes that this should be poured, but this is not necessary. Here I would like to express my Dilletan opinion on this matter.

Scrolling through the E34.SU forum, I highlighted several oils and the theory of what we need to pour and what not.

So, pouring into BMW engines SHOULD be completely synthetic oil, with a viscosity index better than 40-50.

A viscosity index of 60 for older engines can be detrimental. Since the engines have a large amount of soot, and the oil is very thick, all channels of the oil “circulation” are eventually clogged. But at the same time, with this oil, the amount of noise from the engine may decrease and it may stop eating too much of it.

A viscosity index of 30 will be too thin and the engine will probably eat a lot of oil. Usually oils with this index are semi-synthetic.

You need to change the oil every 7-10t.km.

Flush the engine with special means- Not recommended. Because the engine is old, then this tool can kill it. In the same time good oil has engine cleaning products. And it will be better to change it more often than to wash it. A slight mixing of oil (for example, when changing the oil in the engine, oil remains when draining) of different manufacturers and different types- permissible.

Oil must comply with BMW Longlife-01 certification

So, now the manufacturers of oils that I have highlighted:
Motul 8100 Xcess 5W-40
Mobil 1 Peak Life 5W-50
Castrol EDGE SAE 0W-40
Castrol SLX Professional Longtec 0W-40
Liqui Moly Molygen 5W-50

But in Russia, the production of oil under Castrol differs from the oil that is produced in Germany. Therefore, if you want to pour Castrol, then better pour original BMW oil, it costs not so much space money.

All these oils are good, to some extent, if you buy them in trusted places, from official dealers. And not in the transition for 100r.

Recommended engine oils for BMW Group engines
http://tis.bmwcats.com/doc1104549/
There is a firm of oils Shell, Total, Elf, Aral, BP, Agip, Addinol.

In fact, the choice of oil is an individual occupation, you can pour TAZ mineral water and think that you have a BMW. And then tell everyone that a BMW is an expensive car to maintain because you had to capitalize on the engine.

BMW TwinPower Turbo Longlife-01 FE SAE 0W-30 engine oil.

Fully synthetic motor oil based on GTL gas-to-liquid conversion technology. Original BMW Longlife-01 FE 0W-30 engine oil has been specially developed, produced and tested to unlock the full potential of BMW engines, providing them with higher performance characteristics and protection. Compared to standard products, BMW Longlife-01 FE 0W-30 engine oil provides improved fuel efficiency, which allows BMW engines to fully realize the potential of EfficientDynamics technologies.

Advantages:
– Proven fuel economy for petrol engines under the New European NEDC Driving Cycle is at least 1.0% better than BMW Longlife-01 products.
– Consistent performance over a wide range of operating temperatures and engine loads, even under extreme operating conditions.
– Easier cold start at low temperatures.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.
– High level of wear protection.

Applicability:

– For petrol engines since 2002 of release. Currently these are: N1x, N2x, N4x, N54, N55, N63, N74 and others.

BMW approval: Longlife-01FE
Viscosity class according to SAE: SAE 0W-30
Quality class according to ACEA: A5/B5
API quality class: SN

BMW M TwinPower Turbo SAE 10W-60 engine oil.

Engine oil BMW M TwinPower Turbo SAE 10W-60 is specially formulated for BMW M engines.
GTL's innovative base oil technology provides engine protection that exceeds industry standards. This engine oil keeps BMW M engines optimally clean and allows them to reach their full potential.
The engine oil has been extensively tested and approved for use in BMW M engines.
This engine oil is approved by BMW for use as an all-weather oil.

Advantages:
– Provides exceptional dynamic qualities of BMW M engines.

Applicability:
Use strictly in accordance with the instruction manual for your car!
Fits M5/M6/Z8 up to and including 2010. For M3 - until 2013 inclusive.

BMW approval: BMW M
Viscosity class according to SAE: SAE 10W-60
Quality class according to ACEA: A3/B4

BMW M TwinPower Turbo Longlife-01 SAE 0W-40 engine oil.

BMW M TwinPower Turbo Longlife-01 SAE 0W-40 engine oil has been specially developed for BMW engines and the new generation of BMW M engines. GTL's innovative base oil technology provides engine protection that exceeds industry standards. This engine oil keeps BMW and BMW M engines optimally clean and allows them to reach their full potential. The engine oil has been extensively tested and approved for use in BMW engines as well as in the new generation of BMW M engines. This engine oil is approved by BMW for use as an all-weather oil.

Advantages:
– Provides exceptional dynamic qualities of BMW and BMW M engines.
– Confident engine start at low temperatures.
– Excellent wear protection.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.

Applicability:
Use strictly in accordance with the instruction manual for your car!
– For BMW petrol engines and diesel engines without particulate filter.
&ndash For everyone BMW cars M except:
– M5/M6 with release date up to 2011
– M3 with release date before 2014

BMW approval: Longlife-01
Viscosity class according to SAE: SAE 0W-40
Quality class according to ACEA: A3/B4

BMW TwinPower Turbo Longlife-01 SAE 5W-30 engine oil.

Engine oil BMW TwinPower Turbo Longlife-01 SAE 5W-30 is based on GTL technology. This provides engine protection that exceeds industry standards. This engine oil keeps BMW engines optimally clean and allows them to reach their full potential.

Advantages:

– Confident engine start at low temperatures.
– Excellent wear protection.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.

Applicability:
Use strictly in accordance with the instruction manual for your car!
– For all BMW petrol engines.

BMW approval: Longlife-01
Viscosity class according to SAE: SAE 5W-30
Quality class according to ACEA: A3/B4

BMW TwinPower Turbo Longlife-04 SAE 0W-30 engine oil.

BMW TwinPower Turbo Longlife-04 SAE 0W-30 engine oil is based on GTL technology. This provides engine protection that exceeds industry standards. This engine oil keeps BMW engines optimally clean and allows them to reach their full potential.
Compared to conventional motor oils, it is characterized by improved viscosity-temperature characteristics, providing high fuel efficiency.
The new genuine BMW engine oil makes it possible to use the full potential of BMW engines.
This engine oil has been extensively tested and approved by BMW as an all-weather oil.

Advantages:
– Consistent performance over a wide range of operating temperatures and engine loads.
– Confident engine start at low temperatures.
– Excellent wear protection.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.

Applicability:
Use strictly in accordance with the instruction manual for your car!

BMW approval: Longlife-04
Viscosity class according to SAE: SAE 0W-30
Quality class according to ACEA: C3

BMW TwinPower Turbo Longlife-04 SAE 5W-30 engine oil.

BMW TwinPower Turbo Longlife-04 SAE 5W-30 engine oil is based on GTL technology. This provides engine protection that exceeds industry standards. This engine oil keeps BMW engines optimally clean and allows them to reach their full potential.
Compared to conventional motor oils, it is characterized by improved viscosity-temperature characteristics, providing high fuel efficiency.
The new genuine BMW engine oil makes it possible to use the full potential of BMW engines.
This engine oil has been extensively tested and approved by BMW as an all-weather oil.

Advantages:
– Consistent performance over a wide range of operating temperatures and engine loads.
– Confident engine start at low temperatures.
– Excellent wear protection.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.

Applicability:
Use strictly in accordance with the instruction manual for your car!
– For all BMW diesel engines with and without particulate filter.
– Application in gasoline engines bmw
valid only in the EU region, including Norway, Switzerland and Liechtenstein.

BMW approval: Longlife-04
Viscosity class according to SAE: SAE 5W-30
Quality class according to ACEA: C3

BMW TwinPower Turbo Longlife-12 FE SAE 0W-30 engine oil.

BMW TwinPower Turbo Longlife-12 FE SAE 0W-30 engine oil contributes to fuel economy, maintains optimal cleanliness, provides a high degree of protection for BMW engines and allows them to be used to their full potential.
The Low-SAPS formula protects the diesel particulate filter from contamination.
This engine oil has been developed specifically for BMW engines and differs from conventional engine oils in that it allows engines to fully realize the potential of EfficientDynamics technologies.
The engine oil has been extensively tested for performance and approved by BMW as an energy-saving and all-weather oil.

Advantages:
– Proven fuel economy diesel engines according to the parameters of the new European driving cycle NEDC is a minimum of 1.5%.
– Consistent performance over a wide range of operating temperatures and engine loads.
– Confident engine start at low temperatures.
– Excellent wear protection.
– Patented active cleaning technology protects against deposits and corrosion, thus extending engine life.
– Low oil consumption.
– New additive package composition with reduced content of ash-forming substances.

Applicability:
Use strictly in accordance with the instruction manual for your car!
– This oil is only approved for certain new generation BMW diesel and petrol engines. Please contact your BMW dealer for information on applicability.
– Use in BMW petrol engines is only permitted in the EU region, including Norway, Switzerland and Liechtenstein.

BMW approval: Longlife-12FE
Viscosity class according to SAE: SAE 0W-30
Quality class according to ACEA: C2

ENGINE OIL BMW TWINPOWER TURBO.

Engine oil is one of the most important operating materials of modern high-powered BMW engines. BMW engines traditionally place very stringent demands on its properties. In order to be approved for use, engine oil must not only have excellent lubricity, but also have special properties and perform a number of necessary functions:

• energy saving

  The oil must allow the engine to operate using Efficient Dynamics technology: help reduce internal losses, increase fuel efficiency and provide exceptional dynamic qualities. New engine specifications BMW oils The LL12FE and BMW LL14FE+ enable new and future BMW engine models to achieve unrivaled fuel economy performance.

• detergents

  During operation, various contaminants are inevitably formed in the engine. The oil should wash them away and take them to the oil filter, preventing the formation of deposits.
  

• Anti-corrosion

  The oil must protect against corrosion and not be aggressive to friction surfaces and engine parts.
  

• Starting and viscosity-temperature

  The oil must perform equally well in cold engine starts at extremely low temperatures and in operating conditions at high temperatures as well as at higher speeds.
  

• Cooling and sealing

  Any BMW engine is the brainchild of high innovative technologies. During operation, some friction surfaces are heated to very high temperatures and the oil must continuously remove the heat generated. Also, the oil has the function of sealing the combustion chamber, allowing you to achieve excellent power and fuel-economic characteristics of the engine.
  

• Durability

  Oil is one of the main operating materials for ensuring the operation of the engine, so oxidation resistance, low aging rate and low oil waste consumption are among its key qualities.

The whole range of these characteristics was taken into account by BMW engineers when developing new original engine oils. Created by them latest line oils has absorbed all the most advanced achievements in the field of engine oil production technologies. The entire line covers the needs and takes into account the peculiarities of the operation of BMW vehicles in many parts of the world. This also applies to countries with a harsh climate and unstable fuel quality, where there is a high risk of failure of expensive elements of the exhaust gas toxicity reduction system. The production of genuine BMW engine oils is based on the GTL* technology complex, which makes it possible to obtain crystal-clear base oils from natural gas.

Therefore, by using original BMW TwinPower Turbo engine oil, you can be completely sure that your car's engine is protected by high technologies, even in the most difficult modes and operating conditions.

1. Timely visit your official BMW dealer for the next replacement of the original BMW TwinPower Turbo engine oil at the interval prescribed by the manufacturer, or following the instructions on-board computer your car;
2. Check the engine oil level at least once every two weeks using your BMW's dipstick. Electronic system automatic control of the level and quality of the oil will inform you in a timely manner about the need to top up or replace the oil.
3. Buy genuine BMW TwinPower Turbo engine oil only from official dealer centers bmw. Only in this way you can protect yourself and your car from counterfeit products and get the highest quality goods.