Automotive brake system can be called one of the most important in the operation of the car, because without it there can not be more than one vehicle. Therefore, for the perfect operation of the brakes, it is necessary that the elements of the system are reliable. Not an exception is VAZ brake fluid, in this publication we will figure out what kind of liquid is needed and after what period of time it is necessary replacement brake fluid .
Not every motorist knows that the fluid in the brake system needs to be changed from time to time. Some people think that it is only necessary to periodically top up the brake fluid so that air particles do not enter the system, which will impair the performance of the brakes. However, this opinion is not entirely correct, although you should not refuse this operation. The fact is that during the period of operation of the car, moisture forms in the drive of the brake system, which it safely absorbs. brake fluid. The presence of moisture in the liquid is no less dangerous than the presence of air in it, since the work in this case becomes inefficient and corrodes. Based on this, it is recommended that brake fluid replacement was carried out not only on the recommendation of the manufacturer, but also with self-detection of moisture and air in it.
How to tell if your brake fluid needs replacing
As a rule, the manufacturer in the lists of work performed during the scheduled Maintenance, determines its brake fluid change interval for each vehicle individually. For example, this interval is 45,000 km. mileage or at least after three years of operation. The replacement period can also be affected by the type of brake fluid and the design of the brake system. However, car owners are advised to make a visual inspection of the liquid from time to time, while paying attention to its color. If looking into brake fluid reservoir, you will see that it has a dirty tint, this indicates that some elements are worn out, respectively, in this case, its full diagnostics are recommended. If the liquid has a brownish tint, this is a sign that water is present in it. In any of the above cases, brake fluid replacement.
What brake fluid is needed for a VAZ
All brake fluid has its own classification, which indicates its composition and properties. At the moment, there are several brands of TJ - DOT 3, 4, 5 and 5.1., There is also another outdated type of BSK brake fluid, which is still used on old cars.
- DOT 3 It is made on a glycol basis, which includes anti-corrosion and lubricating additives. DOT 3 is recommended for low speed vehicles with front and rear drum brakes. DOT 3 brake fluid reacts poorly to negative temperatures and at -40 degrees its viscosity increases, which negatively affects the operation of the brake system. Consequently, it is not advisable to fill in such a liquid on vehicles operated in the northern regions.
- DOT 4 It is also made on a glycol basis, but unlike DOT 3, it contains additives that increase the boiling point of the brake fluid, which allows it to be used on high-speed cars, where during braking, the decelerating mechanisms are exposed to high temperatures.
- DOT 5 It is made on a silicone basis and also has rather high temperature conditions - 180-260 degrees. With and lower viscosity 900 sq. mm/s Brake Fluid 5 is more suitable for cars with powerful wheels, which are usually fast and difficult driving.
- DOT 5.1 Glycol-based, but with DOT 5 properties. Increased boiling point, more anti-corrosion additives, and low viscosity - 900 sq.m. mm / s., used on cars with powerful mi.
- BSC- this type includes those made on the basis of Butyl Alcohol and Castor oil, hence the given abbreviation in the name. It has very low indications of boiling of TJ (115-120 degrees C), as well as at - 20 gr. it crystallizes, which brings the brake system of the car out of working order.
Can brake fluids be mixed?
Theoretically, brake fluids based on the same component, for example, DOT 3, DOT 4, DOT 5.1 contain glycol, must be mixed, however, due to the presence of a certain set of additives in them, this can only be done in extreme cases, after which a complete replacement of the brake fluid is mandatory. It is impossible to use TZ in a brake system that is designed for a certain type, for example, a DOT 5 bay, which is made on a silicone basis, in a system for DOT 3, DOT 4, DOT 5.1, rubber drive elements (cuffs, seals) may fail.
Keywords: brake fluid, brake fluid replacement, vaz brake fluid, brake fluid reservoir, what brake fluid, dot brake fluid, dot 4 brake fluid, dot brake fluid
We recommend choosing the class of fluid that AvtoVAZ recommends, that is, DOT-4. To determine the brand or manufacturer, you can rely on the reviews of VAZ car owners. According to the survey, about 66% of motorists buy brake fluid from RosDOT, Dzerzhinsk. And not in vain, because in the tests of the ZaRulem magazine, he is in good positions:
- SINTEC EURO DOT-6 (class 6)
- ROSDOT 6 DOT 4 (Class 6)
- SINTEC SUPER DOT 4
- Lukoil DOT 4
- Hi-Gear DOT 4
- ROSDOT 4
- Sibiria Super DOT 4
- Dew 4
- Felix DOT 4
- VITEX DOT 4
- RSQ PROFESSIONAL EURO DOT 4
- HIMLUX DOT 4
- UNIX DOT 4
- PROMPEK DOT 4
Test results for DOT-4 brake fluids. All brake fluids of the same class are compatible with each other. And are they different from each other? The answer to this question is given by the experts "Behind the wheel".
|
Boiling temperature |
Reduced low temperature viscosity** |
Present Unit Value |
Final score |
|||
|---|---|---|---|---|---|---|
|
Lukoil DOT 4 |
||||||
* More is better. ** Less is more.
Can I mix DOT-3, DOT-4, DOT-5 or DOT-5.1
Differences in brake fluid classes:
- DOT 3 (glycol base) - for relatively slow-moving vehicles with drum brakes or disc front brakes;
- DOT 4 (glycol base) - on modern high-speed vehicles with predominantly disc brakes on all wheels;
- DOT 5.1 (glycol base) - on road sports cars where the thermal loads on the brakes are much higher.
- DOT 5 (silicone) is practically not used on conventional vehicles.
Brake fluids DOT 3, 4, 5.1 (color from light yellow to light brown) are interchangeable, but it is not recommended to mix them (it is better to perform a complete replacement), the properties may deteriorate. DOT-5 (dark red) cannot be mixed, it only mixes with itself. In other words, brake fluids can only be mixed by color.
What brake fluid do you recommend? Is it worth changing the DOT-4 class familiar to Lada to others, for example, DOT-5.1? Recall that you can easily find any information about your car by the content (Niva, Priora, Kalina, Grant, Largus, Vesta, XRAY).
Keywords: brakes lada xray| brakes lada vesta | brakes lada largus | brake fret grant | brakes lada viburnum | brakes lada priora | cornfield brakes | universal article
Rosdot-4 brake fluid was developed specifically for vehicles with disc brakes, taking into account the recommendations of AvtoVAZ specialists. Today Rosdot-4 is one of the best in its class among the world's analogues. It is recommended to replace the brake fluid every 1.5-2 years. This is due to the high level of its hygroscopicity. When using Rosdot-4, it is not recommended to add another brake fluid, as this will lead to a deterioration in the properties of Rosdot-4, and, as a result, a decrease in the efficiency of the brake system.
Brake Fluid Specifications
| Parameter | Meaning |
| GOST, TU | TU 2451-004-36732629-99 |
| Appearance | transparent homogeneous liquid from light yellow to light brown without mechanical impurities |
| Viscosity kinematic, mm²/s, at -40°C, no more | 1450 |
| Kinematic viscosity, mm²/s, at -50°C, not less than | 5,0 |
| Kinematic viscosity, mm²/s, at -100°C, not less than | 2,0 |
| Boiling point of dry liquid, °C, not less than | 260 |
| Humidified liquid boiling point, °C, not less than | 165 |
| Stability at high temperature change in boiling point, °C, no more | 3,0 |
| Indicators of activity of hydrogen ions (pH), units pH, within | 9,5-9,0 |
USEFUL TIPS
In order not to expose yourself to unforeseen expenses for the repair of the brake system, and even the entire Lada Grant car as a whole, in the future, replace the brake fluid with fresh one in a timely manner. It is very hygroscopic and absorbs moisture from the air, which, in addition to corroding parts of the brake system, lowers the boiling point of the fluid itself, and this can lead to brake failure during frequent heavy braking. Do not reuse brake fluid drained from the brake system: it is contaminated, saturated with air and moisture.
If brake fluid comes into contact with wires, plastic or painted parts of the body, they can be damaged, so always use a clean wiping cloth when pouring. If liquid comes into contact with these parts, wipe them off immediately with a clean rag.
1. Check the brake fluid level in the master cylinder reservoir. When the plug is removed, it should be between the "MIN" and "MAX" marks applied to the tank body. With the plug installed, the brake fluid level should be at the lower edge of the filler neck, as the brake fluid is displaced by the float of the level sensor.
WARNING
A gradual drop in the brake fluid level with no leaks most likely indicates the need to replace the brake pads. Check the condition of the brake pads on the Lada Grant car (see "Checking the degree of wear of the brake pads, brake discs and brake drums"). Untimely replacement brake pads leads to costly repairs (replacement of brake pads, brake discs and brake drums)!
We perform work on a viewing ditch or overpass.
We pump out the old liquid from the tank with a syringe or a rubber pear.
Attention! Brake fluid that has entered paintwork, plastic parts and vehicle wiring may damage them. Remove it immediately with a clean rag.
Pumping to replace the fluid is carried out at idle engine first on one circuit, and then on the other in the following sequence:
- brake mechanism, right rear wheel;
- brake mechanism left front wheel;
- brake mechanism of the left rear wheel;
- brake mechanism of the right front wheel.
We clean the bleeder valve from dirt brake mechanism right rear wheel.
The assistant should vigorously press the brake pedal to the stop 1-2 times and keep it pressed.
Loosen the bleed screw 1/2-3/4 turn.
Loosen the bleed screw 1/2-3/4 turn.
In this case, fluid will flow out of the hose. As soon as the liquid stops flowing out of the hose, we wrap the fitting, and only after that the assistant can release the pedal. We repeat this operation until new brake fluid comes out of the fitting (lighter than the old one). We remove the hose, wipe the bleeder dry and put a protective cap on it.
We put a hose on the fitting, and immerse its free end in a container partially filled with working fluid.
Similarly, we pump the brake mechanisms of another circuit.
When pumping, you need to monitor the level of fluid in the tank and add fluid.
After pumping the hydraulic drive of the brakes, we bring the fluid level in the reservoir to normal.
You can also partially replace the fluid in the clutch hydraulic drive. Complete replacement liquid without dismantling all components will not occur, since the clutch slave cylinder, combined with the clutch release bearing, is a kind of "hydraulic dead end". The bleed valve is located in the middle of the line, and it is not possible to replace all the liquid through it. Stirring the liquid will refresh it somewhat.
We put a hose on the fitting, and immerse its free end in a container partially filled with working fluid.
We sink the wire clamp in the direction of the red arrow and push the plastic tube in the direction of the green arrow by 7–9 mm.
Brake fluid is used not only to organize the operation of the brake system, but also to ensure the smooth movement of clutch mechanisms, as is the case with the Lada Kalina car.
This is explained by the fact that in this model the clutch and brake mechanisms have the same principle of operation. By pressing the pedal, brake fluid is injected to the brakes, as well as to the clutch mechanism, due to which the braking of the entire car is ensured.
What brake fluid should be used on the Lada Kalina
During operation, it is recommended to use brake fluids manufactured by ROSDOT 4 and NEVA-M, as their products are of the highest quality and most suitable for this car compared to others.
The difference between the two is the cost, and the first option will cost a bit more. As for the original fluid that is poured into the car, AvtoVAZ uses DOT 4.
In this case, the liquid may differ in composition depending on for which vehicle it is intended. Below is a table with the brake fluids used.
also in Lada Kalina you can use DOT 5.1. It differs from the rest in a more viscous consistency and a higher boiling point. According to the manufacturer, this fluid is replaced every five years.
In the case of Kalina, it is recommended to change the fluid about once every 45 thousand kilometers or every two years. This is explained by the fact that during operation, the fluid loses its original properties, which negatively affects the operation of the elements of the brake system.
How to refill brake fluid
First of all, it is worth noting that spoiled brake fluid can be identified due to its darkened color and thickened consistency. Replacement will require the following materials and tools:
- New brake fluid.
- Syringe to remove old fluid.
- Dry rag.
- Container for draining old fluid.
- Rubber hose, the hole of which must fit under the bleed fittings on the wheels of the car.
- Brake wrench 8 x 10 mm.
Where is the liquid
You can find brake fluid in brake hoses. It is also found in:
- master cylinder;
- brake tank.
It is worth noting that almost every experienced owner Lada Kalina knows where the brake system is located and how it works. If there is no such knowledge, then it is better to study the structure of the car before replacing it, or still seek help from professionals at the service station.
When choosing an option self replacement The first step is to carry out preparatory work:
- Install the car on a flyover or pit.
- Turn off the engine and install wheel chocks.
- Disconnect the terminals from the battery.
Drain
First of all, during the replacement, the old fluid is drained. It is performed as follows:
- The tank needs to unscrew the lid. It contains brake fluid. The lid can be put aside, but it is better to lay a rag under it, since the composition is in excellent contact with the surrounding surfaces, not affecting them very well.
- The next step is to unlock the pressure regulator on rear wheels ah, if it proves necessary. To unlock this design, you will need to install a screwdriver between the plate and the piston.
- After that, you should prepare a hose and a container for draining the old fluid. Best of all, if there is no container at hand, use an empty bottle. Before draining, it is necessary to clean the fitting from dirt with a brush. Subsequently, a hose will be attached to the fitting.
- As soon as the fitting is cleaned, you will need to remove the cap from it and insert one end of the hose into the hole, and the other should go into a container or bottle. Then you need the help of a second person. He will need to get into the car and press the brake pedal several times. This must be done abruptly so that the liquid can be drained, but between each press it is necessary to maintain a short break.
- As soon as the liquid stops flowing, it is necessary to pull the hose out of the hole, wipe the fitting with a rag and close it with a lid. In this case, it is necessary to tighten the cover correctly. So, for example, if in the process of unscrewing it was loosened by 3/4, then it should be tightened by the same amount.
- The final action will be the beginning of the bay of the new composition while tightening the fitting. As soon as new liquid begins to flow out of the existing hole, you can tighten the cap completely.
This fluid drain diagram is for the rear brakes. As for the front, the procedure is practically no different. The main difference is only in the location of the fittings, but this will not be a problem if you familiarize yourself with the structure of the car and the brake system in advance.
Thus, the brake fluid is drained from both the front and rear brakes, after which it will be possible to start filling in new fluid.
gulf
Filling with liquid is required during the drain procedure. In this case, both actions should not be performed simultaneously, but in a certain sequence. In other words, it is impossible to fill in a new liquid composition until at least half of the old one is drained.
When carrying out work, several points should be considered:
- Air must not be allowed to enter the brake system. This leads to a deterioration in the performance of the brake pedal - the resistance changes.
- It is impossible for bubbles to also be in a bottle or in a hose. If such a situation has arisen, then it is impossible to fill in new fluid until the entire brake system is pumped and air is removed from it.
After the replacement is completed, reassembly is carried out necessary elements and check by turning on the engine. If there are no problems, then the amount of liquid in the tank is additionally checked, and if necessary, topping up to the required volume should be carried out.
Brake fluid in a Lada Kalina car is an important component, thanks to which safe control all vehicle.
Therefore, it is worth monitoring the condition of the liquid, as well as its level, in order to avoid serious problems and replace it in a timely manner. It should also be noted that in some situations, old brake fluid or fluid leakage can be the root cause of a serious accident, as in this case the car's brakes simply will not work.
We perform work on a viewing ditch or overpass.
We unscrew the cap of the filler neck of the tank.
We pump out the old liquid from the tank with a syringe or a rubber pear.
Fill the reservoir with new brake fluid.
Attention! Brake fluid that comes into contact with paintwork, plastic parts, and vehicle wiring can damage them. Remove it immediately with a clean rag.
It is necessary to bleed the hydraulic drive of the brake system until new fluid (lighter than the old one) begins to come out of the bleeders of all working cylinders.
We carry out pumping to replace the fluid with the engine off, first on one circuit, and then on the other in the following sequence:
- brake mechanism of the right rear wheel;
- brake mechanism of the left front wheel;
- brake mechanism of the left rear wheel;
- brake mechanism of the right front wheel.
Before pumping, we check the level of the working fluid in the reservoir of the hydraulic brake drive. Add liquid if necessary.
We carry out bleeding of brakes with the assistant. We clean the bleeder valve of the brake mechanism of the right rear wheel from dirt.
Remove the protective cap from the fitting of the cylinder of the rear right wheel.
The assistant should vigorously press the brake pedal to the stop 1-2 times and keep it pressed.
Using the “8” key, unscrew the bleeder valve by 1/2-3/4 turn.
In this case, fluid will flow out of the hose, and the brake pedal should be pressed all the way.
As soon as the liquid stops flowing out of the hose, we wrap the fitting, and only after that the assistant can release the pedal.
We repeat this operation until new brake fluid comes out of the fitting (lighter than the old one).
We remove the hose, wipe the bleeder dry and put a protective cap on it.
Remove the protective cap from the bleeder valve of the brake mechanism of the left front wheel.
We put a hose on the fitting, and immerse its free end in a container partially filled with working fluid.
We pump, as described above, the brake mechanism of the left front wheel, unscrewing the bleeder valve with the “8” key.
Similarly, we pump the brake mechanisms of another circuit.
When pumping, you need to monitor the level of fluid in the tank and, if necessary, add fluid.
After pumping the hydraulic drive of the brakes, we bring the level in the fluid in the reservoir to normal.
There is an even easier option for changing the brake fluid. This method does not require the presence of an assistant. In this case, a certain supply of brake fluid (at least 1 liter) is desirable.
We install the car on an inspection ditch or overpass and provide free passage between the place where you can replenish the brake fluid reservoir in engine compartment, and brake cylinders of all four wheels.
We pump out the brake fluid from the tank with a rubber bulb or syringe. Add new fluid to the top edge. To speed up the process (in order to release liquid from all cylinders at once), it is advisable to pick up four pieces of tubes that fit tightly on the bleed fittings of all cylinders. We lower the free ends of the tubes into transparent bottles of a small capacity.
We turn off the fittings of all brake cylinders. We make sure that the liquid has flowed through all four tubes. We control the decrease in fluid from the tank located on the brake cylinder, and immediately replenish the tank. We observe an increase in the level of liquid in bottles located near the wheel brake cylinders.
It is necessary to move several times from the position of monitoring the outflow of fluid from the fittings of the brake cylinders to the position where you can check and replenish the fluid level in the reservoir located on the brake cylinder in order to prevent the reservoir from draining.
Usually the level rises most rapidly in the bottle into which the hose coming from the brake cylinder of the front left wheel is lowered. As soon as there is about 200 ml of liquid in the bottle of the front left wheel, we wrap and tighten the fitting of this cylinder. Next, we wait for the same result at the cylinder of the front right wheel, and also wrap its bleed fitting. You can complete the process after 200-250 ml of liquid comes out through the fitting of each rear wheel.
We make sure that all fittings are tightly tightened. We put on protective caps. We specify the fluid level in the reservoir of the main brake cylinder.
The Lada Grant car has a brake system (pipelines, brake cylinders, a vacuum booster, a brake regulator, brake pads etc.) similar to the car Lada Kalina. For effective and safe braking, Lada Granta uses a diagonal, dual-circuit piping system, which means that the first circuit blocks the wheels - the right front and left rear, and the second circuit - the left front and right rear. The front wheels are equipped with disc brakes, the rear wheels are equipped with drum brakes. The master brake cylinder is controlled through a vacuum brake booster, which increases the efficiency of operating the brake system by pressing the brake pedal. Depending on the configuration of the Lada Granta car, the braking system can be equipped with an anti-lock braking system (ABS). The Lada Granta car has a hand brake that blocks the rear wheels (spreads the brake pads in the drums). The pads are bred through a system of levers, by moving a steel cable fixed to a lever located in the passenger compartment. vacuum booster on a Lada Granta car (shown in Fig. 1) of a diaphragm type. The diaphragm is a separating partition between the rarefied atmosphere created in the vacuum amplifier and the external atmospheric pressure. The pressure difference reduces the force on the brake pedal. When the brake pedal is released, the vacuum and atmospheric chambers communicate with each other through a special valve.
Rice. 1. Scheme hydraulic system brakes Lada Granta (without ABS): 1, 25 - brake mechanisms of the right front and left front wheels; 2, 24 - brake hose for supplying brake fluid to the right and left front wheels; 3,4, 15, 18, 21, 5,10,13,22,27 - pipelines of the hydraulic brake system; 6 - plastic reservoir of the brake master cylinder; 7 - the main cylinder of the hydraulic drive of the brakes; 8 - vacuum amplifier; 9, 30 - pipe holders; 11 - flexible hose of the brake mechanism of the right rear wheel; 12, 17- brake mechanism of the right rear wheel; 14, 31 - brackets for fastening flexible hoses; 16- flexible hose of the brake mechanism of the left rear wheel; 19 - elastic lever drive pressure regulator; 20 - pressure regulator; 23 - brake pedal; 24 - flexible brake mechanism of the left front wheel; 26 - circuit tee right front - left rear brake; 28 - circuit tee left front - right rear brake; 29 - tee mounting bolts
Features of the Lada Grant braking system with ABS are shown in Figure 2.
Fig. 2. Scheme of the Lada Grant hydraulic brake drive (with anti-lock braking system): 1, 14, 22 - brackets for fastening flexible hoses; 2 - brake mechanism of the right front wheel; 3 - flexible hose of the brake mechanism of the right front wheel; 4, 5, 15, 18, 26 - pipelines of the circuit right front - left rear brake; 6, 10, 13, 27, 28 - circuit pipelines left front - right rear brake; 7 - plastic tank of the main brake cylinder; 8-vacuum amplifier; 9, 24 - pipe holders; 11 - flexible hose of the brake mechanism of the right rear wheel; 12 - brake mechanism of the rear wheel; 16 - brake mechanism of the rear left wheel; 17 - flexible hose of the brake mechanism of the left rear wheel: 19 - brake pedal; 20-brake mechanism of the left front wheel; 21 - flexible hose of the brake mechanism of the left front wheel; 23 - the main cylinder of the hydraulic drive of the brakes; 25 - ABS hydroelectronic module
Rice. 3. Vacuum booster of the car Lada Granta: 1 - flange for fastening the tip; 2 - stock; 3 - diaphragm return spring; 4 - sealing ring of the flange of the main cylinder; 5 - main njhvjpyjq cylinder; 6 - amplifier pin; 7 - amplifier housing; 8 - diaphragm; 9 - amplifier housing cover; 10 - piston; 11 - protective cover of the valve body; 12-pusher; 13- pusher return spring; 14-valve spring; 15 - valve; 16 - stock buffer; 17- valve body; A - vacuum chamber; B - atmospheric chamber; C, D - channels Information on the principles of operation of the Lada Granta brake system components, in particular the main brake cylinder and pressure regulator (the pressure regulator is installed only on cars without ABS) can be found in the article “Design features of the brake system of a Lada Priora car”, the design of the nodes is similar .
We carry out bleeding of the hydraulic drive of the brake system after its repair, which resulted in a violation of the tightness of the system and if air is suspected to enter the system. In the latter case, you must first determine and eliminate the cause of air entering the hydraulic drive and only then start pumping it. The presence of air in the hydraulic drive of the brake system is determined by the behavior of the brake pedal: it becomes soft (no stop is felt at the end of the pedal stroke) and falls below its normal position.
You will need an assistant to complete the work, as well as:
Special wrench for bleed valve or 8 mm spanner wrench;
Transparent vinyl tube of suitable diameter;
Container for draining brake fluid;
Inspection ditch or overpass (desirable).
We prepare the car for work.
Disconnect the wiring harness connector from the low brake fluid level sensor connector and remove the reservoir cap
In order to avoid air ingress into the hydraulic drive of the brake system while pumping the drive, make sure that the level of brake fluid in the reservoir does not fall below the mark MIN.
If a rear axle the vehicle is hung out (the vehicle is on a lift or mounted on stands), the pressure regulator will block the path of the brake fluid to the rear wheel cylinders, therefore, to bleed the rear wheel cylinders, it is necessary to open the regulator valve.
To open the pressure regulator valve, insert the blade of a slotted screwdriver between the lever and the plate, sinking the regulator stem.
9. Bleed the brakes on the remaining wheels, if necessary.
In the absence of air in the system, the brake pedal must be "hard", i.e. when pressed, go no more than half the distance to the floor.
Brake Fluid Replacement
To complete the work, you will need an assistant, as well as a rubber bulb.
1. We prepare the car and the necessary equipment for the work.
2. Remove the tank cover
To prevent air from entering the hydraulic drive of the brake system, when changing the brake fluid, make sure that its level in the reservoir does not fall below the mark MIN.
3. With a pear, we select the working fluid from the reservoir of the main brake cylinder.
4. Pour new fluid into the tank up to the top edge of the tank.
5. We pump the contours of the hydraulic drive system, starting from the rear wheels of the car.
6. We carry out bleeding of each wheel cylinder before the new (lighter) brake fluid starts to exit from the fitting.
7. After replacing the fluid in both circuits, we check the operation of the hydraulic drive and bring the fluid level in the reservoir of the main brake cylinder to normal.
The brake fluid in the hydraulic brake drive system on modern Lada models (Grant, Kalina, Priora, Niva 4x4, Vesta and XRAY) should be replaced every three years or after 45,000 km (whichever comes first). On Lada Largus - once every six years or after 90 thousand km. run. All cars have the same type of brake design, so the process for changing brake fluid is similar.
Brake Fluid Replacement (Method #1)
The traditional, familiar way to replace the brake fluid in the hydraulic brake system by substitution. The order of pumping for modern cars Lada (Granta, Kalina, Priora, Largus, Vesta and XRAY) - rear right, front left, rear left, front right wheels. For Niva 4x4 - rear right, rear left, front right, front left.
- Pump out the liquid from the tank (with a syringe or rubber bulb);
- Fill in new brake fluid;
- Remove the protective cap from the fitting of the brake mechanism, loosen the tightening of the fitting with a wrench and put on the hose (immerse the other end in a container half filled with liquid).
To force the brake fluid to flow out of the fitting, an assistant will be required, who must press the brake pedal 1-2 times, and then hold it with his foot. Instead of an assistant, you can put a spacer or create pressure in the tank using a special lid or lungs (covering your mouth with a rag). We considered such methods of pumping brakes without an assistant earlier.
As soon as a lighter liquid runs instead of a dark one, we move on to another wheel according to the circuit diagram (see above). Periodically check the level of the brake fluid in the reservoir and add it if necessary, otherwise air will enter the brake system.
Replacing the brake fluid (method number 2)
On certain cars (for example, Lada Vesta, Largus, XRAY with French JH3 / JR5 boxes) there is an easier way to change the brake fluid - use the clutch bleeder. It will take less time, but the brake fluid will only be partially replaced.
We put a hose on the fitting (immerse the other end in a container half filled with liquid). Next, the pipeline should be depressurized, for this we lower the bracket down (No. 4) and pull out the plastic tube (No. 1, to the right) by 7-9 mm. We drain about 150 ml of liquid (with or without an assistant, see above) and seal the circuit back. Check the brake fluid level in the reservoir. This process is in detail.
Recall that brake fluid that gets on the paintwork, plastic parts and wiring of the car can cause damage. Clean surfaces of brake fluid immediately. Do you change brake fluid yourself? What difficulties did you experience during the first change? By the way, do you know which brake fluid is better to choose?