The procedure for changing the oil in a manual transmission for a Hyundai Getz does not require professional skills. automaker Hyundai Getz called the recommended replacement period - 75 thousand kilometers or after 5 years of operation of the vehicle. In Russian realities, such a period is reduced to 40-60 thousand kilometers.
Why is it necessary to change the oil in a manual transmission?
Any oil in a car (engine or manual transmission) consists of a standard oil fluid and additional additives. The quality of the oil is determined by the chemical composition, and additives serve to improve performance in a particular case.
The main functions of oils: lubrication of the component moving parts that form friction between themselves. Additional function: removal of heat that results from this friction.
The main reason for changing the oil is the loss of performance of additives. Over time, components lose their properties and cease to provide high-quality protection for work units. After a few hundred kilometers, a rumble will begin to be emitted from the box, and after a certain number of kilometers traveled, the box will jam. Therefore, the periodic replacement of motor oil in a manual transmission with a Hyundai Getz is a mandatory procedure.
Oil leakage and breakdowns
List of causes of oil leakage from the gearbox Hyundai car getz:
- Damaged oil seals. Inside the manual transmission, an increased operating pressure, which affects the seals. They wear out gradually. There are gaps through which oil escapes. Solution: replace the stuffing box and eliminate the increased working pressure in the system;
- Input shaft wear. The result is the appearance of play, through the holes of which the oily liquid begins to flow. The box is completely disassembled. Status is assessed. Solution: replace the shaft or install an additional gasket (depending on the amount of backlash);
- The tightness of the connections is insufficient. Check all connections for stains. Solution: replace the seal if there is a lack of sealing of the connecting parts;
- Oil drain plug or dipstick. Solution: the plug must be tightened or the sealing ring must be changed. The probe must be installed correctly in accordance with the operating instructions for the vehicle.
The process of changing the oil in the manual transmission
List of required tools:
- Set of wrenches;
- A set of hex keys;
- Pharmacy syringe;
- Pliers;
- Screwdriver;
- Container for draining waste liquid.
Step-by-step instructions for draining old oil from a manual transmission Hyundai Getz:
Flushing the pallet in the manual transmission on the Hyundai Getz is carried out with special chemical compounds and using a metal brush. To do this, you need to unscrew the oil pan, drain the residual amount of oil and clean it from metal chips and other debris.
Step-by-step instructions for filling oil in a manual transmission in a Hyundai Getz:
- Pull the dipstick out of the fill plug.
- Pour oily liquid into the hole with a funnel.
- After 3 liters of liquid, insert the dipstick back, pull it out and look at the level. If necessary, you will have to add lubricant.
Note: For simple Hyundai Getz models, check the oil level and fill it through the gearbox housing. To do this, you can also use a pharmacy syringe or a special device.
After filling the oil, the plug closes and it is necessary to drive about 10 kilometers. The level of the filled fluid is rechecked. If it is not enough, you need to add a little. If the level is normal, the process of replacing the car oil in the manual transmission with the Hyundai Getz is completed.
Changing the oil in the automatic transmission Hyundai Getz, manual transmission once in a given time period will keep the car in working order and prevent serious breakdowns. The procedure is carried out together with other operations. regular maintenance TS. Work can be done independently or in a technical service - it all depends on their type, complexity. It is difficult to make a complete replacement in an automatic transmission, a partial one in an automatic transmission or a standard one in a manual transmission can be done without any problems with your own hands. It is necessary to choose a transmission fluid strictly taking into account the manufacturer's recommendations, the volume for flushing should be taken into account separately.
When to change the oil at the Getz gearbox
In the box, the machine uses a special ATF liquid - this is not pure oil. It performs the following functions:
- provides the transfer of torque from the crankshaft to the input shaft;
- is responsible for engaging a particular gear by passing optimum pressure on friction clutches of clutch units;
- removes heat from the gearbox, removes it to the atmosphere;
- lubricates all rubbing parts, thereby preventing premature wear and scuffing.
The transmission fluid needs to be changed from time to time, another option is to check the level and top up. During the operation of the car, ATF evaporates - this is a natural process that cannot be avoided. If the oil volume is normal, individual light fractions evaporate - active substances that give the transmission the desired properties. Also, over time, the additives develop their initial resource.
Important! Resource transmission fluid specified in the vehicle owner's manual.
Making the bay into the box optimally through a funnel
Oil in a Goetz manual box must be filled in every 15 thousand kilometers, in an automatic transmission - at least every 75 thousand km. In practice, in the first case, maintenance is done after 10 thousand, in the second - after 40. The exact interval will depend on the driving style, operating conditions of the car, and the quality of the working fluid used. You also need to monitor the shade of the oil - it can become darker, but not lighter.
What kind of oil to fill in the Hyundai Getz box
For replacement Hyundai oils Getz needs to use a quality product that meets the manufacturer's recommendations. Compatibility is important - for example, original ATF SP III products or compatible Mitsubishi Diamond ATF SPIII are optimally suited for Hyundai. The car market has a wide selection of oils, so there is an option for any budget (but it is important not to forget about quality).
Important! When replacing one oil with another (in terms of type), flushing must be done, in other cases - at the discretion of the car owner.
The right choice of product is the key to the successful operation of the vehicle
How much oil is needed in a Getz box
To change the oil in a Getz box, you need to prepare:
- 3-5 liters for automatic transmission with partial replacement (upgrade);
- 6-8 liters for automatic transmission at full;
- 15 for manual transmission.
Separately consider the transmission fluid for flushing the gearbox. It needs at least 2 liters.
How to fill oil in a Hyundai Getz box
The procedure for changing the Getz gearbox oil depends on the type of unit. More on all options below.
Before starting work, you need to gain access to the gearbox - from the bottom of the car
Oil change in automatic transmission Hyundai Getz
In the box, the Hyundai Getz automatic oil change can be done in two ways - partial or complete. It is difficult to refill 100% with your own hands - you need to contact the service station.
Complete oil change in automatic transmission Getz
There is no equipment in the garage for carrying out complete replacement transmission fluid. Only the master in the service should carry out such work. It is mandatory to use a flyover or a viewing hole. You can independently drain about 60% of mining or less - 100% will not leak out.
Partial oil change in a Getz automatic box
For partial replacement oil in the automatic transmission in the garage, you need to prepare a watering can, keys, transmission fluid, a container where mining will drain, a new filter. Work instructions:
View of the gearbox automatic transmission Goetz
Partial replacement will update the fluid by 40%. This is enough to improve the quality of the automatic transmission. You can carry out the procedure in 3 stages or steps - drain and fill in oil three times, maintain a mileage of 300 km between procedures. So it will turn out to change around 70%.
Changing the oil in a manual transmission Hyundai Getz
To carry out the procedure, they take a set of hexagons, wrenches, a syringe from the first aid kit, a screwdriver, pliers, a container for working out. Steps for changing the oil in the Getz mechanic's box:
- Burn out the engine, install the car in a pit, lift or overpass - you need full access to the bottom of the car.
- Remove the rubber cap, wash it, put it back in place.
- Place an empty container under the drain plug, unscrew. Wait until the working out flows out (the procedure takes up to half an hour).
- Rinse the manual transmission pan using special chemicals, brushed. Unscrew the oil pan, drain the remaining automotive oil, remove chips and other debris.
- Remove the dipstick and check the oil level.
- Pour new fluid into a special hole using a funnel.
- After 2-3 liters of liquid, return the dipstick to its place, remove it again and check the level.
- Close the drain hole, drive about 10 km.
It will be necessary to perform a final level check, if necessary, adjust the amount of liquid.
13 bolts must be removed
Important! IN simple models Getz Hyundai the content of the working fluid is checked through the crankcase. Filling is carried out in the same way.
It is important to check not only the level, but also the condition of the transmission
How to check the oil in a Hyundai Getz box
It is imperative to monitor the oil level in the Hyundai Getz box to eliminate leaks. Their reasons:
- Damage to oil seals - inside the manual transmission, automatic transmission, pressure rises during operation, it has a negative effect on the oil seals, they wear out with the formation of cracks. Items can only be replaced.
- Input shaft wear - play will appear, oil will flow through its holes. The box is disassembled, an accurate assessment of its condition is carried out, the shaft is replaced, a new gasket is made.
- Poor tightness of connections - you need to check them for stains, replace the seal if there are problems with the sealing of the connections.
- The drain plug is loose - it needs to be tightened, sometimes replacing the o-ring helps. The probe is also checked, installed according to the operating instructions for the car.
- An oil check is done every 15 thousand km, as often as possible. It is desirable to carry out work on a viewing ditch or overpass.
Procedure:
- Clean the crankcase around the inspection hole with a rag.
- Use a wrench to loosen the filler plug.
- Unscrew the plug manually until the end.
- If there is a worn washer under the plug, replace it.
- Check the transmission fluid level - it should be near the lower edge, slightly higher.
- Adjust the oil content if necessary using a syringe.
It remains to check the level again, if everything is in order, then tighten the plug.
The service life of the Getz gearbox depends on the level of ATP fluid
Important! During the test, it is advisable to drop oil on paper or cloth. A bad sign is not only a lack of liquid, but also a strange smell, color.
Conclusion
An oil change in an automatic transmission Hyundai Getz needs to be done every 40-70 thousand kilometers, in a manual transmission - 10-15 thousand. A partial update is easy to do on your own, the procedure full shift in automatic transmission is complex, requires the use of a whole set of equipment - it is carried out in service centers. The level in the gearbox should also be checked regularly, since the working fluid tends to evaporate during operation.
It is necessary to check the oil level in the gearbox every 15,000 km of run, as well as when oil leaks are found on the gearbox crater.
We carry out work on a flyover or a viewing ditch.
We check the oil level through the control (filler) hole, which is located in front of the gearbox housing.
With a rag we clean the gearbox housing around control hole.
Loosen the filler plug with a spanner wrench or a “17” head.
Finally unscrew the plug by hand.
A metal sealing washer is installed under the plug.
Replace the defective washer with a new one.
The oil level in the gearbox should be at the level of the lower edge of the filler hole, which can be checked with a finger.
If necessary…
... with a syringe for filling transmission oil add oil to the gearbox to the lower edge of the hole (oil will begin to flow out of the hole).
When excess oil flows out, remove oil drips with a rag.
We wrap the cork with a moment of 30-42 N ∙ m.
It is necessary to change the oil in the gearbox every 90 thousand kilometers.
Before changing the oil, warm it up by driving the car for at least 10 km. It's best to schedule an oil change after a long trip.
We clean the gearbox housing around the drain and filler holes.
We substitute a container with a volume of at least 2.5 liters under the drain hole.
With a spanner wrench or a “24” head, loosen the drain plug tightening ...
... and finally turn the cork out by hand.
Drain the oil into a container.
The connection between the plug and the gearbox housing is sealed with a metal washer.
If necessary, replace the sealing washer of the drain plug with a new one. We clean the cork magnet and wrap the cork with a torque of 35-45 N ∙ m. Using the “17” key, unscrew the filler plug. Pour gear oil into the gearbox with a syringe to the required level and wrap the plug (see above).
Read also:
- Transmission oil: where to buy consumables for the gearbox? Today, there are a huge number of consumables ...
- Repair mechanical box programs in Perm: professional help in a difficult matter. The gearbox is a complex...
- Today automotive market full of variety engine oils from different manufacturers, which also differ in quality characteristics and ...
- The most important unit of a car is the engine. During operation, the car engine is subjected to heavy loads, which leads to ...
- How to get to Vnukovo Airport by taxi quickly and comfortably? Vnukovo Airport is located southwest of the capital…
According to technical regulations, in the Hyundai Solaris gearbox, oil is poured for the entire life of the car. Depending on the type of gearbox, checking the oil level is carried out at different periods and according to different methods. In order not to bring the gearbox to expensive repairs, check the oil level in time and correctly.
Filling new oil through the dipstick.
When servicing any of the gearboxes, automatic or manual, a filling syringe is very useful, since it is hardly possible to add or change oil using a simple funnel. Unless you have to design an extension for the neck of the funnel from a hose.
Checking the level of the transmission in the automatic transmission is carried out at least every 60,000 km, but it is advisable to do this more often, and an oil change may be necessary after repair of the box or transmission fluid wear.
Algorithm
The check is carried out in the following order:
- We warm up the engine to operating temperature, the engine must be warmed up to 70-80 degrees, and the check is carried out no later than 10-15 minutes after the engine is stopped.
- We install the car on a flat area and, with the engine running, put the automatic transmission selector in position N or P.
- Carefully wipe the area near the probe with a rag. This is necessary to ensure that debris does not get into the box.
- We turn off the engine and when the oil drains into the automatic transmission pan, remove the dipstick from the gearbox crankcase.
The automatic transmission dipstick is marked with a red arrow.
- We diagnose the condition of the oil. To do this, take a white napkin and blot the probe. The oil should be transparent, if it has darkened, has a burning smell, if small solid particles remain on the napkin, it is advisable to replace the oil. If there are small brown fractions, suspension, this will indicate increased wear of the friction clutches.
This is what pure oil looks like.
- We add if necessary.
If necessary, add oil to the automatic transmission. This is it.
- We wipe the probe with a clean rag and put it back in place, into the tube to the end. Now check the oil level. Normal level - the oil film is between the two HOT marks. If the oil level is low, it must be topped up. It is important not only to observe the optimal level, but also not to exceed it, since there is a risk of accelerated wear of oil seals and automatic transmission mechanisms.
If the level check is carried out on a cold engine, then the oil level must be between the two "cold" marks C. The principle is the same - if the level is below normal, top up without exceeding the allowable level.
Oil type
Automatic transmission oil of ATF SP-III standard.
The oil used in the Solaris automatic transmission is ATF SP-III standard of any manufacturer.
Video about automatic transmission repair on Hyundai Solaris
Checking the oil level in a manual transmission on a Hyundai Solaris
Oil in manual transmission.
IN manual transmission standard oil is used SAE 75W-90(original - HYUNDAI GENUINE PARTS MTF 75W-90 ), according to the applicability standard API-GL4.
Algorithm
The check is done like this:
The normal level is along the bottom edge of the plug thread. If, after removing the plug, the oil does not appear, we check the presence of oil with a thin screwdriver or a finger, if necessary, top up with a filling syringe.
Control plug near.
We pay attention to the aluminum sealing gasket on the cork - if it is strongly compressed, it must be replaced. We twist the stopper of the control hole.
So you can quickly check the oil level in the gearbox yourself and top up if necessary. Good luck to everyone and happy travels!
It is necessary to check the oil level in the gearbox every 15,000 km of run, as well as when oil leaks are found on the gearbox crater.
We carry out work on a flyover or a viewing ditch.
We check the oil level through the control (filler) hole, which is located in front of the gearbox housing.
With a rag we clean the gearbox housing around the control hole.
Loosen the filler plug with a spanner wrench or a “17” head.
Finally unscrew the plug by hand.
A metal sealing washer is installed under the plug.
Replace the defective washer with a new one.
The oil level in the gearbox should be at the level of the lower edge of the filler hole, which can be checked with a finger.
If necessary…
... with a syringe for filling transmission oil, add oil to the gearbox to the lower edge of the hole (oil will begin to flow out of the hole).
When excess oil flows out, remove oil drips with a rag.
We wrap the cork with a moment of 30-42 N ∙ m.
It is necessary to change the oil in the gearbox every 90 thousand kilometers.
Before changing the oil, warm it up by driving the car for at least 10 km. It's best to schedule an oil change after a long trip.
We clean the gearbox housing around the drain and filler holes.
We substitute a container with a volume of at least 2.5 liters under the drain hole.
With a spanner wrench or a “24” head, loosen the drain plug tightening ...
... and finally turn the cork out by hand.
Drain the oil into a container.
The connection between the plug and the gearbox housing is sealed with a metal washer.
If necessary, replace the sealing washer of the drain plug with a new one. We clean the cork magnet and wrap the cork with a torque of 35-45 N ∙ m. Using the “17” key, unscrew the filler plug. Pour gear oil into the gearbox with a syringe to the required level and wrap the plug (see above).
www.koreacentre.ru
Oil change in manual transmission - logbook Hyundai Getz GLS 2007 on DRIVE2
On the threshold of TO 90, it's time to change the oil in the box. flooded original oil, I decided to change semi-synthetics 85W-90 to synthetics 75W-90, also original.
Oil HYUNDAI/KIA, 75W-90: 043005L1A0
Let's start with an oil change. To begin with, having climbed on the Internet, I tried to find a normal manual, which shows the drain and filler holes for oil in the manual transmission. Having found several photographs, but still not understanding all the coordinates, I had to climb and look for myself. Perhaps someone will come in handy.
We substitute the container, take the knob (key) for 24 and unscrew the drain bolt. The oil begins to drain, dark in color, smelly ... :)
After the oil is drained, unscrew the filler bolt, and make the filler pipe. I got this one - stupid, simple, but effective :)
We place it under the hood, insert the pipe into the filler hole.
This is necessary in order to wash deposits and old black, dirty oil from the very bottom of the box. I also advise you to do this when changing the oil in the engine.
After clean oil has flowed from the drain hole of the box, we take the cork and remove chips and small particles from it. There is a magnet in the gearbox oil drain bolts that collects all the small metal particles that appear in the oil during operation.
After that, we wrap the cork and pour oil under the neck of the filler hole.
The total volume of filled oil is ~ 2.2 - 2.4 liters.
Issue price: 820 ₽ Mileage: 90,000 km
www.drive2.ru
3.28 Checking the transmission oil level in the manual gearbox
Checking the transmission oil level in the manual gearbox
Checking the gear oil level in the manual gearbox (after 30,000 or 24 months)*
On early models, the transmission fluid dipstick is located at the front of the transmission and does not require jacking up the vehicle to access it. The location of the filling, level and drain plugs manual transmission (late models)
|
Automn.ru
Hyundai Getz | Checking the level and adding oil to the gearbox | Hyundai Getz
Service maintenance and operation
Manuals ￫ Hyundai ￫ Getz (Hyundai Getz)
You will need: a key "for 13", a syringe.
7. Replace the oil filler plug and place the protective cap on it.