Description of the truck crane "Galicianin" KS-65713-5
Automobile hydraulic crane KS-65713-5 has a load capacity of 50 tons. The crane installation is mounted on a four-axle chassis of a KamAZ-6560 vehicle with an 8×8 wheel arrangement. This truck crane is designed to perform loading, unloading, construction and installation work with poor access roads. single wide profile tyres, powerful engine chassis, the ability to change tire pressure while driving depending on the road surface, the chassis has interaxle and interwheel locks, including on all four wheels of the rear bogie at the same time - all this makes this crane indispensable in hard-to-reach places with poor road conditions, in off-road conditions.
Crane hydraulic system provides smooth control of all mechanisms with a wide range of speed control of working operations. Simultaneous combination of several working operations is possible. The lifting unit is driven by hydraulic pumps. Lifting mechanisms are individually driven by hydraulic cylinders and hydraulic motors.
Crane installation steel structures are made of high quality WELDOX steel. Crane booms are manufactured according to modern world standards of crane construction, from bent all-metal profiles, have a non-rectangular section with a lower chord in the form of an ellipse. The length of the boom in the folded state is 11.5 m, which allows the truck crane to provide the necessary compactness and maneuverability when moving. In working condition, the length of the boom is 34.1 m, which provides an extensive working area and the highest height of movement of the load during operation. The ability to extend the boom with the load allows the truck crane to perform tasks of varying complexity, such as carrying loads among installed structures, installing them in hard-to-reach places. Maximum size of the support contour is 7.0 m by 7.0 m, this area is achieved through the use of a non-standard design of the lower frame and outriggers. Thanks to this design, the truck crane has the ability to carry out lifting operations in a circular area. The ability to carry out these works allows you to minimize the number of necessary permutations of the crane during work at the facilities.
For this crane it is possible to install additional removable counterweights, weighing 10 tons, which significantly increases the load-altitude characteristics of the crane. Installation of additional counterweights in the working position is carried out without the use of additional lifting equipment and human resources.
Gearboxes for lifting mechanisms and rotation of a planetary type crane with disc brakes, which meets modern requirements for hoisting machines. Many crane units use imported components that do not require replacement and repair for the entire period of the crane's service life. An autonomous diesel heater is used to heat the crane driver's cab.
Set of instruments and devices provides necessary security crane. A device such as a microprocessor load limiter automatically provides protection against overturning and overloads.
Load-altitude characteristics of the truck crane "Galichanin" KS-65713-5, based on KAMAZ-6560, all-terrain vehicle, with a carrying capacity of 50 tons:
 |
Technical characteristics of the truck crane "Galichanin" KS-65713-5, based on KAMAZ-6560, all-terrain vehicle, with a carrying capacity of 50 tons:
| Maximum load moment, t.m | 160 |
| Maximum load capacity, t / reach, m | 50/3,2 |
| Boom length, m | 11,5 - 34,1 |
| Gooseneck length, m | 9,1; 15,1 |
| Maximum hook lifting height, m | |
| - with main boom 34.1 m | 34,5 |
| - with main boom 34.1 m and jib 15.1 m | 50,4 |
| Max. hook lowering depth by boom 11.5 m at reach 5.0 m, m | 8,0 |
| Mass of cargo at which extension of boom sections is allowed, t | 6,0 |
| Load lifting-lowering speed, m/min | |
| - nominal (with a load weighing up to 50.0 tons) | 3,6 |
| - increased (with a load weighing up to 10.0 tons) | 7,2 |
| - maximum (multiplicity of chain hoist 1) | 38,0 |
| Load landing speed, m/min | 0,15 |
| Turning part rotation frequency, rpm | from 0.1 to 1.2 |
| Crane travel speed under its own power, km/h | up to 40 |
| Support contour size along x across the chassis axis, m | |
| - with fully extended outriggers | 7.2 x 7.0 |
| - with outrigger sections retracted | 6.73 x 4.63 |
| Crane weight in transport position, t | |
| - with main boom, without counterweights | 38,8 |
| Wheel formula of the base vehicle | 8 x 8 |
| Base vehicle engine | diesel |
| - model | KAMAZ-740 |
| - power, hp | 400 |
| Crane dimensions in transport position, m, (length x width x height) | 13.9 x 2.5 x 3.99 |
| Operating temperature, deg. With | -40 to +40 |
The beginning of the production of truck cranes Galichanin dates back to 1982, when, by order of the government of the USSR, the Krasny Excavator plant was redesigned into a truck crane. The machine received its own name, often indicated on the arrow next to the alphanumeric index, from the location of the enterprise. Cranes used throughout Russia and beyond are made in Galich, a city in the Kostroma region, located 600 km from Moscow.
Description
In different years of production, the Galichanin crane was mounted on the chassis of KrAZ, MAZ, Ural and KamAZ trucks. The drive of the installation is standard: from the engine of the base car through a power take-off. Hydraulics is independent: from hydraulic pumps and motors. The control allows you to vary the speed over a wide range, as well as simultaneously combine two crane operations. The ability to telescoping the boom (not on all models) allows you to deliver goods to hard-to-reach places.
The customers highly appreciated the cranes, which are installed on the KamAZ chassis, for good maneuverability, a wide range of spare parts and the ability to travel on city roads, which significantly expands the range of construction sites. car engine KAMAZ is unpretentious in maintenance, meets all environmental standards. It is easily repairable, which in turn minimizes crane downtime. On the basis of KamAZ, the plant offers models with a carrying capacity of 25 to 50 tons.
Truck crane modifications
The line of models of the plant began with a carrying capacity of 16 tons. Such cars were produced during the years of the collapse of the Union. Russian production started with a mark of 20 tons, then changed to 25 tons, but development does not stop. The use of Volvo chassis and close cooperation with Belarusian developers made it possible to produce a truck crane with a maximum lifting capacity of 100 tons.
Models have different specifications, differ in the length of the boom, the ability to work in hard-to-reach places and the presence of additional crane equipment. An interesting feature A separate development of the plant is the possibility of installing an additional counterweight in the kit to the main one, which allows expanding the scope of the crane. Most models have the ability to build an arrow with a jib of different lengths, so you can increase the height of the load and much more.
25 tons
The minimum load capacity of the Galichanin truck crane available for order is 25 tons. In this class, the customer is offered a large set of models. They differ in the length of the boom (from 21 to 40 m), the height of the load (24-26 m) and even the wheel formula.
Depending on the expected conditions of use, you can get a 25-ton truck crane based on KamAZ 43118 with a drive on all 6 wheels and 65115 with a steam drive rear axles. For special conditions, there is a novelty, which is based on an 8x4 wheel arrangement.
Even with the same boom length, the Galician 25 tons of technical characteristics will vary. Models based on the Urals, having an arrow of 21 m, lift the load to a lower height. Models on the KAMAZ chassis have a small headroom (for the length of the lines).
See » TOP-3 models of domestic erection cranes based on MKT tractors
32 tons
Galician KS-55729 has a carrying capacity of 32 tons. This model is produced on the Russian KamAZ chassis, Belarusian MAZ and imported Volvo. Despite the fact that the ability to lift the maximum load is the same, the length of the boom for modifications is different, while it directly depends on the wheel formula of the base vehicle.
A Galician 32 t based on a rear-wheel drive KamAZ 6x4 has a boom of 31 m and a maximum load moment of 102 t.
With an arrow of 30.2 m, KAMAZ KS-55729-1v Galichanin is supplied. This 8-axle has indicators identical to the Belarusian. The crane KS-55729-4v, which is based on imported Volvo, has the same moment and boom. Model 5v received a chassis from KamAZ, but is positioned as a truck crane for particularly difficult conditions: 4 axles, four-wheel drive on 8 wheels, KamAZ 63501 is taken as the basis.
50 tons
Truck crane Galichanin 50 tons is offered to the consumer not only on the basis of different base vehicles, but also in different designs. For standard conditions, 8-axle vehicles with full or partial drive are offered, based on the chassis from KamAZ or the Belarusian Tractor Plant (MZKT). The maximum boom length is 34 m, the load moment is 160 t. m.
There are also models of compact cranes in this weight category. With the help of this Galician, the customer will be able to work in the conditions of small construction sites, at some distance from the object under construction and lift the load to a great height due to the boom of 40 m. The rest of the indicators are identical to those described above, up to the chassis.
60 tons
When creating Galichanin for 60 tons, the plant refused to use the KamAZ chassis. The base vehicles for this modification were 4-axle Volvo and MZKT of the Belarusian plant. For difficult building conditions, the latter option can be assembled on the basis of an all-wheel drive vehicle (8x8).
The maximum reach of the boom is 42 m. When using a jib, it can be extended up to 57 m. positive quality truck crane is the ability to work in hard-to-reach places and at great distances from the parking lot.
Other models
The creation of Galicianin 70 tons went on rolled rails: the variant described above had already been created earlier. Therefore, this crane did not receive any special innovations. Arrow of the same length, there is a possibility of its extension.
See » How is the installation and dismantling of a tower crane at a construction site
But the base cars for this version were others. For example, model KS-74721-2 Galicianin H&H. For its production, a Belarusian chassis with a wheel arrangement of 10x6 was used. Three axles are located under the crane part. Car drive - all three. Additional letters of the name describe the control system. In the crane operator's cabin, a German digital panel developed by a special order of the plant is mounted.
This model was removed from the product catalog, but the plant also had another one: Galician 80 tons. It is based on the same 5-axle Belarusian chassis, an arrow 48 m long, the possibility of extension is not provided. Load moment - 283 t. m.
100-ton versions are also made on five axles. This is the upper limit of the products offered by the plant. Arrow - 51 m with the possibility of extension up to 69 m; chassis - Volvo or MZKT; load moment - 355 t. m.
For particularly difficult construction conditions, the plant's engineers proposed a KC-59713-14T truck crane, where T means a tractor chassis. The machine has caterpillar drive, made on the basis of the forestry tractor TL-5ALM. The main figures indicate a load capacity of 25 tons. The boom is 23.6 m long, it is possible to increase it in single file up to 9 m. The load moment developed by the model is 85 t.m.
The USA-2 model based on the KS-55729-5M has become a universal soldier. The customer is offered a crane of 32 tons, a diesel hammer for driving piles and a pair of cargo winches. All components necessary for the operation of any option are included in the delivery kit.
In addition to truck cranes, the plant can offer other products. For example, KMU-150 Galician. This is a loader crane, installed both on trucks and separately. The properties of this model include ease of installation and the ability to install on a flatbed truck, while the latter does not lose its ability to carry goods.
The manipulator is mounted in the dead zone, between the cab and the body. In most cases, it has the ability to turn the hook 360 °. The plant offers several onboard KamAZ trucks with an already installed manipulator, as well as a special model, where instead of a cargo suspension there is a mounting cradle.
Advantages and disadvantages of technology
Repair of the Galichanin truck crane can be carried out in specialized centers located in different regions of Russia. If the crane works in the Moscow, Yaroslavl or Kostroma region, you can not look for a point, but contact the manufacturer immediately. The plant has a service center for its products, where, taking into account the features and technical characteristics of the machine, they will do everything necessary to ensure that the crane works as long as possible and brings profit to the customer.
Regardless of the model, the machine will factory within warranty period repaired free of charge.
The advantages of Galichanin cranes include the following characteristics:
- The production takes into account all modern developments and GOSTs that exist in crane and lifting equipment.
- The booms of the new truck cranes of this brand are made of bent profiles, connected by butt welding to the full length. This scheme reduces the weight of the boom, while at the same time increasing the load capacity of the machine.
- Turbocharged engine. At a truck crane, most of the time the engine rotates idly, the turbine only wastes fuel in vain.
- Creating the younger models of the line, the developers tried to save wherever possible. This led to some disadvantages. For example, on 25 ton cranes with a 21 m boom, the front outriggers are located almost next to the turntable. This limits the turning radius.
- The absence of mudguards under the panel leads to rapid corrosion.
- Many note that the Galician is assembled on a chassis platform, while the Ivanovets is one with the car.
The disadvantages of many users include:
Price
The cost of a Galician consists of several components:
- chassis;
- load capacity;
- arrow length (if there are several options).
A crane based on the Urals will cost less than a similar model based on KamAZ. A crane of 25 tons with a boom length of 21 m will cost almost 2 times cheaper than the same, but with a boom length of 40 m. The Volvo chassis will be more expensive than the MZKT, KamAZ - cheaper.
According to the manufacturer's prices, the cost of the basic configuration of the Galician starts from 7.5 thousand rubles.
Truck crane Galichanin 25 tons based on KamAZ is an automobile jib crane, which is used for construction, high-altitude, utility and rescue work. The device has a load capacity of 25 tons. Mounted on the chassis of Kamsky cars car factory. Performs loading and unloading operations. The design is characterized by high maneuverability, cross-country ability, can be operated in off-road conditions, during temperature extremes, snowfalls and ice. The manufacturer cares about the quality of all components, so the cars are reliable for drivers and can be easily used on construction sites.
Advantages and disadvantages of technology
Among the key advantages of the models are:
- Large crane boom length, which allows you to lift loads to the desired height.
- High load capacity, which provides the possibility of loading and unloading operations of any volume.
- The technical characteristics of the truck crane Galician 25 tons comply with all modern standards and requirements.
- The high speed of telescoping the boom makes it possible to carry out construction, installation, loading and unloading operations as quickly and easily as possible.
- The chassis is different cross-country ability, thanks to which the design can be used even in off-road conditions.
- Increased bearing capacity.
- Increased wear resistance and durability of equipment.
As for the shortcomings, this is, first of all, the cost, so this equipment is best rented. Renting a truck crane will cost much less than buying it and further maintenance, sale repair work, as well as conducting regular preventive examinations and paying salaries to drivers and operators.
Modifications
The device of the truck crane Galichanin 25 tons based on KamAZ comes in various models, including:
- KS 55713 - 1
- KS 55713 - 1 V
- KS 55713 - 3
- KS 55713 - 4.4 V
- KS 55713 - 5.5L, 5V
- KS 55731 - 4
They differ in the type of chassis that equip the model. The following chassis can be used: 65115, 43118, 6540, 65222. The wheel formula is also different, sometimes 6x6 and 6x4.
Specifications
Consider the technical characteristics of the truck crane Galichanin 25 tons based on KamAZ using the model KS 55713-1 as an example.
| Parameter | Meaning | ||
|---|---|---|---|
| Maximum load moment, t.m | 80 | ||
| Maximum load capacity, t / reach, m | 25/3,2 | ||
| Boom length, m | 9,7 — 21,7 | ||
| Gooseneck length, m | 9 | ||
| Maximum hook lifting height, m | |||
| - with main boom 21.7 m | 21,9 | ||
| - with main boom 21.7 m and jib 9 m | 30,0 | ||
| Max. hook lowering depth by boom 9.7 m at reach 5.0 m, m | 12 | ||
| Mass of cargo at which extension of boom sections is allowed, t | 4,0 | ||
| Load lifting-lowering speed, m/min | |||
| - nominal (with a load weighing up to 25.0 tons) | 5 | ||
| – increased (with a load weighing up to 6.0 tons) | 12 | ||
| - maximum (multiplicity of chain hoist 1) | 96 | ||
| Load landing speed, m/min | no more than 0.3 | ||
| Turning part rotation frequency, rpm | from 0.15 to 1.4 | ||
| Crane travel speed under its own power, km/h | up to 60 | ||
| Support contour size along x across the chassis axis, m | |||
| - with extended beams of outriggers | 4.2 x 5.6 | ||
| - with retracted beams of outriggers | 4.2 x 2.28 | ||
| Wheel formula of the base vehicle | 6 x 4 | ||
| Base car engine: | diesel | ||
| - model | Cummins ISB6.7e4 300 | ||
| - power, kWt | 219 | ||
| Crane dimensions in transport position, m (length x width x height) | 12 x 2.5 x 3.6 | ||
| Operating temperature, deg. With | -40 to +40 | ||
| Normative service life of a truck crane, years | 12 |
The device and controls of special equipment
The truck crane Galichanin 25 tons has a special drive of the crane installation, which is realized thanks to two axial-piston hydraulic pumps. They begin to rotate by moving the gearbox and power take-off. The turntable has an individual drive, there is an independent control from the hydraulic hammer and hydraulic cylinder. As for the hydraulic system of the equipment, it is characterized by smooth control, it is possible to regulate the speed of the implementation of work operations. It is also possible to simultaneously implement several operations using a crane.
The mechanism of the telescoping system includes a three-section telescopic boom, the length of which on various models varies from 9.7 to 21.7 m. The boom can be in the retracted and extended position. In the retracted position, it is quite compact, so the device can be easily transported, and in the extended position, it easily moves loads to the required height during the implementation of any type of work. Most often, booms are additionally equipped with lattice jibs, due to which the space under the boom itself increases.
The lifting mechanism is extremely simple. The device of the boom of the Galichanin truck crane is made in such a way that the load on the hook evenly distributes its weight, so it is possible to implement various tasks, including loading and unloading operations in a narrow space, installing loads in hard-to-reach places. It is also possible to enable the mode of operation of equipment on supports with retracted beams with outriggers.
There are special devices in the driver's cab that control the safety of the operation of special equipment. This includes a microprocessor load limiter with digital indication of operation parameters, and a black box in which telemetry memory is automatically recorded, and protection of equipment from overvoltage from power lines.
The driver's cab itself is distinguished by increased comfort, high noise insulation and vibration isolation.
As for the chassis, it happens different type. You can basically choose what suits you best. With the type of chassis, the instructions for using the Galician truck crane for 25 tons will help you figure it out.
Manufacturer
The equipment is produced by the Galician Truck Crane Plant, which owns the unique equipment that is used in the manufacture of cranes. Manufacturers take care of all the components, the quality and reliability of the equipment. It is also important to note that the plant does not purchase unnecessary components, in this regard, the cost of special equipment is quite low compared to other equipment. The Galician plant carefully checks all the components and monitors the quality of each part, since the efficiency of the equipment depends on the spare parts. The advanced technologies of the plant have reduced the dynamic load of the equipment, also reduced the coefficient of friction, reduced the force on rotation, and also increased the smoothness of turns.
Analogues
An analogue of Galichanin is the equipment of Ivanovets truck cranes, which has similar technical characteristics and is also distinguished by high performance. Equipment "Ivanovets" is produced by the Ivanovo plant of automobile cranes.
Conclusion
The Galich Truck Crane Plant produces equipment that has a lifting capacity of 25 tons and more. It is characterized by high wear resistance, reliability and long service life. This plant is one of the leading manufacturers of specialized equipment that implements construction, high-rise, utility, installation and handling operations. Special equipment is installed on the basis of domestic chassis, it can be used in snow, ice, and rain, it is not affected by temperature changes. The device itself has an extremely comfortable cab for the driver, a long boom that is capable of lifting loads to the required height. When choosing equipment, you should pay attention to such technical specifications: maximum load capacity, boom reach length, jib length, maximum operating life of equipment, as well as features of its maintenance.
SPETSNEFTEMASH GROUP sells new Galichanin truck cranes to all regions of Russia at prices below factory prices from availability and on order. This catalog contains all current models of Galichanin truck cranes with technical specifications and photos. For more information, please contact the sales department.
Catalog of truck cranes brand Galichanin
Specifications KS-55713-1 Parameter Value Maximum load moment, t.m 80 Maximum load capacity, t/outreach, m 25/3.2 Boom length, m 9.7 - 21.7 Jib length, m 9 Maximum hook lifting height , m - with main boom 21.7 m 21.9 - with main boom 21.7 m and jib 9 m 30.0 Max. hook lowering depth, m 12 Mass of the load at which the extension of the boom sections is allowed, t 4.34 Load lifting-lowering speed, m/min - nominal (with a load weighing up to 25.0 tons) 5 - increased (with a load weighing up to 6 ,34 t) 12 - maximum (multiplicity of chain hoist 1) 40 Load landing speed, m/min, not more than 0.3 Turning part rotation speed, rpm from 0.15 to 1.4 Crane travel speed under its own power, km/h up to 60 Support contour size along x across the chassis axis, m - with outrigger beams extended 4.2 x 5.6 - with outrigger beams retracted 4.2 x 2.28 Base vehicle wheel arrangement 6 x 4 Base vehicle engine: diesel - model Cummins ISB6.7 300 - power, hp (kW) 307(225.6) Crane dimensions in transport position, m (length x width x height) 12 x 2.5 x 3.6 Operating temperature, deg . C from -40 to +40 warranty service crane 18 months from the date of transfer of the crane to the consumer, but not more than 1000 hours of operation Standard service life of the truck crane, years 12 Model description KS-55713-1 unloading and construction and installation works at dispersed facilities. All chassis have excellent maneuverability and ease of control, which allows the crane to be used on sites with various types access roads, and small dimensions make it suitable for operation in the cramped conditions of modern cities. The crane installation is driven by two axial-piston hydraulic pumps, which are driven by the engine of the base vehicle through a gearbox and an additional power take-off. Crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. Hydraulic system crane installation provides smooth control of all mechanisms with a wide range of speed control of working operations, as well as the possibility of simultaneously combining several crane operations. A three-section telescopic boom with a length of 9.7 - 21.7 m in the retracted position provides the crane with compactness and maneuverability when moving, and in the extended position - an extensive working area and a large height of cargo movement during operation. Additional equipment of the boom with a lattice jib 9 m long allows for the largest service area and the size of the under-boom space among similar models of 25 ton cranes. The transfer of the jib from the transport position to the working position and back is carried out manually without the use of additional lifting equipment. The possibility of telescoping the boom with a load on the hook allows the crane to perform special tasks: install loads in hard-to-reach places, carry them among mounted structures. For convenience of work in cramped conditions, a mode of work with loads is provided with the installation of a crane on supports with the beams of outriggers retracted. The safe operation of the crane is ensured by a set of instruments and devices, including a microprocessor-based load limiter with digital indication of operating parameters on the display in the driver's cab. The device automatically protects the crane from overload and overturning, is equipped with a system of coordinate protection of the crane, which is necessary for working in cramped conditions, has a built-in telemetric memory unit ("black box") and a ..
Pages: 1
Price list for truck cranes Galichanin
| Truck crane model | Truck crane chassis | Price with VAT, rubles |
| 100 tons (OVOID) | ||
|---|---|---|
| KS-85713 "Galician". Main boom 51.0 m ovoid profile | Chassis Volvo FM (10x4) EURO-4 | 45 000 000 |
| KS-84713-2 "Galician". Main boom 51.0 m ovoid profile | chassis MZKT (10x4) EURO-4 | 40 500 000 |
| 100 tons (OVOID) - options | ||
| Double-horned hook suspension with a lifting capacity of 100.0 tons | 450 000 | |
| Double folding jib 10.0 m - 18.0 m | 900 000 | |
| Installation of a second (auxiliary) cargo winch complete with a single block ("beak") on the boom head and with an additional hook suspension with a capacity of 5.0 tons. The kit also includes the installation of a video camera for monitoring the winding of the rope cargo swan | 1 500 000 | |
| the maximum set of additional separately transportable counterweights can have total mass 20.0 tons and include 4 counterweights of 5.0 tons each | 600 000 | |
| A set of two additional separately transportable counterweights of 5.0 tons each | 600 000 | |
| 70 tons (OVOID) | ||
| KS-75721 "Galician" H&H (Hydak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile |
Chassis Volvo FM (8x4) EURO-4 | 26 000 000 |
| KS-75721-1 "Galician" H&H (Hyudak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile | Chassis KAMAZ-7330 (10x4) EURO-4 | 23 300 000 |
| KS-74721-2 "Galician" H&H (Hyudak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile | chassis MZKT-750120 (10x4) | 23 300 000 |
| KS-75721-3 "Galician" H&H (Hyudak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile | Chassis MAN (8x4) | 26 000 000 |
| KS-75721-6 "Galician" H&H (Hyudak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile | chassis MZKT-652715 (8x8) | 24 500 000 |
| KS-75721-8 "Galician" H&H (Hyudak and Hirschmann, Germany) basic configuration boom 42.0 m ovoid profile |
chassis Scania (8x4) EURO-5 | 26 000 000 |
| 70 tons (OVOID) - options | ||
| Installation of a second cargo winch complete with a single block on the boom head for working on a single reeving with a crane suspension with a lifting capacity of 3.2t and a video camera for monitoring the winding of the cargo winch rope | 400 000 | |
| Two-knee folding jib 9.1 m - 15.0 m long, with a variable angle of inclination of 0 or 30 degrees from the boom axis, complete with a hook suspension with a capacity of 6 tons. Installation is possible in a configuration with a second cargo winch | 600 000 | |
| Additional, separately transportable counterweight, 4.0 tons (for KS-75721-1 and KS-74721-2, weight 4.3 tons) | 300 000 | |
| 165 000 | ||
| 180 000 | ||
| 60 tons (OVOID) | ||
| KS-65721 "Galician" basic configuration boom 42.0 m ovoid profile | Chassis Volvo FM (8x4) EURO-4 | 24 000 000 |
| KS-65721-2 "Galician" basic configuration boom 42.0 m ovoid profile | chassis MZKT-750110 (8x4) EURO-4 | 20 000 000 |
| KS-65721-6 "Galician" basic configuration boom 42.0 m ovoid profile | chassis MZKT-652715 (8x8) EURO-4 | 22 000 000 |
| 60 tons (OVOID) - options | ||
| Installation of a second cargo winch complete with a single block on the boom head for working on a single reeving, with a hook suspension with a capacity of 3.2 tons and a video camera for monitoring the winding of the cargo winch rope | 400 000 | |
| Two-legged folding jib 9.1 m - 15.0 m long, with a variable angle of inclination of 0 or 30 degrees from the boom axis, complete with a hook suspension with a capacity of 6 tons. Installation is possible in a configuration with a second cargo winch (separately transportable for KS-65721-6) | 600 000 | |
| Set of two additional separately transportable counterweights: - 2 x 3.25 tons for truck cranes KS-65721, KS-65721-2; - for the truck crane KS-65721-6 are included in the basic package. |
375 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Centralized lubrication system for elements and components of a BEKA crane installation (complete with two cargo winches) | 180 000 | |
| 50 tons Compact Crane (OVOID) | ||
| KS-65715 "Galician" basic configuration boom 40 m ovoid profile | chassis VOLVO (8х4) EURO-4 | 21 500 000 |
| KS-65715-1 "Galician" basic configuration boom 40 m ovoid profile | 18 700 000 | |
| KS-65715-3 "Galician" basic configuration boom 40 m ovoid profile | chassis MAN (8х4) EURO-4 | 23 000 000 |
| KS-65715-6 "Galician" basic equipment boom 40 m ovoid profile | 21 000 000 | |
| 50 tons Compact crane (OVOID) - options | ||
| Installation of a second cargo winch complete with a single block on the boom head, with a hook suspension with a capacity of 3.2 tons and a video camera for monitoring the winding of the cargo winch rope | 450 000 | |
| Two-knee folding jib 10 m long - 17.0 m, with a variable angle of inclination 0 ; 20 or 40 degrees from the boom axis, complete with a hook suspension with a capacity of 9.5 t. Installation is possible in a configuration with a second cargo winch | 700 000 | |
| Additional separately transportable counterweight, weighing 5 tons | 300 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Centralized lubrication system for elements and components of a BEKA crane installation (complete with two cargo winches) | 180 000 | |
| 50 tons (OVOID) | ||
| KS-65713-1 "Galician" basic configuration boom 34.1 m ovoid profile | Chassis KAMAZ-65201 (8x4) EURO-4 | 14 450 000 |
| KS-64713-2 "Galician" basic configuration boom 34.1 m ovoid profile | chassis MZKT-750110 (8x4) EURO-4 | 14 450 000 |
| KS-65713-5 "Galician" basic configuration boom 34.1 m ovoid profile (basic counterweights are transported separately from the truck crane) |
18 200 000 | |
| KS-65713-6 "Galician" basic configuration boom 34.1 m ovoid profile | chassis МЗКТ-652715 (8х8) EURO-4 | 18 200 000 |
| 50 tons (OVOID) - options | ||
| Installation of a second cargo winch complete with a single block on the boom head, with a hook suspension with a capacity of 3.2 tons (except for KS-65713-5) | 350 000 | |
| Two-stage telescopic jib with a length of 9.1 m - 15.0 m, with a variable angle of inclination of 0 or 30 degrees from the boom axis, complete with a hook suspension with a capacity of 4.5 tons. Installation is possible in a configuration with a second cargo winch ( except for KS-65713-5). | 600 000 | |
| A set of two additional separately transportable counterweights 2 x 3.0 tons. | 350 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Centralized lubrication system for elements and components of a BEKA crane installation (complete with two cargo winches) | 180 000 | |
| 32 tons (OVOID) | ||
| KS-55729B "Galician" boom 30.2 m ovoid profile | chassis MAZ-6312 (6x4) EURO-4 | 8 750 000 |
| KS-55729-1V "Galician" boom 30.2 m ovoid profile | Chassis KAMAZ-6540 (8x4) EURO-4 | 9 050 000 |
| KS-55729-5B "Galician" boom 30.2 m ovoid profile (additional counterweight and jib are transported separately from the truck crane) |
Chassis KAMAZ-63501 (8x8) EURO-4 | 10 300 000 |
| 32 tons (OVOID) - options | ||
| Additional separately transportable counterweight weighing 2.9 tons for truck crane KS-55729V | 270 000 | |
| Additional separately transportable counterweight weighing 2.4 tons for truck crane KS-55729-5V | 250 000 | |
| Optional 9.0 m jib with 0 or 30 degree tilt from the boom axis | 270 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| 25 tons | ||
| Boom 21.7 m | ||
| KC-55713-1 "Galician" boom 21.7 m | 6 850 000 | |
| KS-55713-3 "Galician" boom 21.7 m | chassis Ural-4320 (6x6) EURO-4 | 6 750 000 |
| KS-55713-4 "Galician" boom 21.7 m | 6 900 000 | |
| KS-55713-5 "Galician" boom 21.7 m | 6 900 000 | |
| 25 tons / boom 21.7 m - options | ||
| For models of the series with a boom length of 21.7 meters: additional equipment with a straight lattice jib 9.0 m long (except for model KS-55713-3) | 220 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Boom 23.7 m OVOID | ||
| KC-55713-1L "Galician" boom 23.7 m ovoid profile | Chassis KAMAZ-65115 (6x4) EURO-4 | 6 950 000 |
| KC-55713-5L "Galician" boom 23.7 m ovoid profile | Chassis KAMAZ-43118 (6x6) EURO-4 | 6 950 000 |
| 25 tons / Boom 23.7 m OVOID - options | ||
| For series models with a boom length of 23.7 meters: additional equipment with a straight lattice jib 9.0 m long with a lifting capacity of 2.6 tons | 300 000 | |
| For the KS-55713-1L truck crane, an additional counterweight weighing 1.35 tons carried in the base or separately | 100 000 | |
| For truck crane KS-55713-5L, installation of a hydraulic portal for the possibility of mounting / dismounting an additional removable counterweight | 80 000 | |
| For the KS-55713-5L truck crane, an additional counterweight weighing 400 kg, carried in the base or separately | 60 000 | |
| For series models with a boom length of 23.7 meters: optional oil cooler | 90 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Boom 28 m | ||
| KC-55713-1B "Galician" boom 28.0 m | Chassis KAMAZ-65115 (6x4) EURO-4 | 7 300 000 |
| KC-55713-3B "Galician" boom 28.0 m | chassis Ural-5557 (6x6) EURO-4 | 7 150 000 |
| KC-55713-4В "Galician" boom 28.0 m | Chassis KAMAZ-65111 (6x6) EURO-4 | 7 300 000 |
| KC-55713-5В "Galician" boom 28.0 m | Chassis KAMAZ-43118 (6x6) EURO-4 | 7 300 000 |
| KC-55713-6B "Galician" boom 28.0 m | chassis MAZ-6312 (6x4) EURO-4 | 7 150 000 |
| 25 tons / boom 28 m - options | ||
| For series models with a boom length of 28 meters: additional equipment with a straight lattice jib 9.0 m long (separately carried for models KS-55713-3V and KS-55713-5V) | 230 000 | |
| For the KS-55713-5V truck crane, installation of a hydraulic portal for the possibility of mounting / dismounting an additional removable counterweight | 80 000 | |
| For the truck crane KS-55713-5V, an additional counterweight weighing 650 kg, carried in the base or separately | 60 000 | |
| For models of the series with a boom length of 28 meters: additional equipment with a tool box for slings and a washbasin | negotiable | |
| For series models with a boom length of 28 meters: optional oil cooler | 90 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Boom 31 m OVOID | ||
| KS-55713-1V-4 "Galician" boom 31 m ovoid profile | Chassis KAMAZ-65115 (6x4) EURO-4 | 7 950 000 |
| KS-55713-5V-4 "Galician" boom 31 m ovoid profile | Chassis KAMAZ-43118 (6x6) EURO-4 | 7 950 000 |
| 25 tons / Boom 31 m OVOID - options | ||
| For series models with a boom length of 31 meters: additional equipment with a 9.0 m long jib made of high-strength steel (can be installed on the head at angles of 0°, 20° and 40° to the boom axis) (separately transportable for model KS-55713-5V-4 ) | 300 000 | |
| For model KS-55713-1V-4 with a boom length of 31 meters: an additional separately transportable counterweight weighing 4.5 tons | 330 000 | |
| For model KS-55713-5V-4 with a boom length of 31 meters: the first additional separately transportable counterweight weighing 1.9 tons | 140 000 | |
| For model KS-55713-5V-4 with a boom length of 31 meters: the second additional separately transportable counterweight weighing 4.5 tons | 330 000 | |
| For series models with a boom length of 31 meters: optional oil cooler | 90 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Boom 40 m OVOID | ||
| KS-55731-1 "Galician" boom 40 m ovoid profile | Chassis KAMAZ-6540 (8x4) EURO-4 | 12 900 000 |
| KS-55731-4 "Galician" boom 40 m ovoid profile | Chassis KAMAZ-65222 (6x6) EURO-4 | 14 400 000 |
| 25 tons / Boom 40 m OVOID - options | ||
| For models in the 40m boom series: 9.0m high strength steel jib with a lifting capacity of 6.3t | 300 000 | |
| For models of the series with a boom length of 40 meters: installation of a second cargo winch complete with a single block on the boom head and with an additional hook suspension with a capacity of 3.2 t | 450 000 | |
| For series models with a boom length of 40 meters: additional equipment with a counterweight weighing 3.5 tons | 300 000 | |
| Centralized lubrication system for elements and assemblies of a BEKA crane installation (complete with one cargo winch) | 165 000 | |
| Centralized lubrication system for elements and components of a BEKA crane installation (complete with two cargo winches) | 180 000 | |
| Universal pile driving unit | ||
| Universal pile driving unit USA-2 based on KS-55729-5M with a lifting capacity of 32 t (basic equipment: 18.7 m mast; diesel hammer with a shock part weight of 1250 kg; two cargo winches; hook suspension | Chassis KAMAZ-6560 (8x8) EURO-4 | 21 500 000 |
| Universal pile driving unit - options | ||
| Cradle with a capacity of 250 kg for lifting people to a height of up to 12 m | 200 000 | |
| Hydraulic rotator with a force of 85 kN * m for screwing screw piles | 1 450 000 | |
| Hydraulic rotator with a force of 15 kN * m for drilling | negotiable | |
| Diesel hammer with maximum weight shock part 1800 kg | negotiable | |
| Crane-manipulator installation | ||
| Crane-manipulator-150 | 2 130 000 | |
| Crane - options | ||
| Installation of KMU-150 "turnkey" on the customer's car | Vehicle modification required. Vehicle certification cost not included | 200 000 |
| Rear beam with two rear outriggers, retractable hydraulic cylinders, complete with two rear swivel support hydraulic cylinders (outriggers), complete with hydraulic piping | specification of vehicle modification is required | 200 000 |
Galician 25 tons is designed for loading and unloading and construction and installation works at dispersed objects. All chassis have excellent maneuverability and ease of control, which allows the crane to be used at facilities with various types of access roads, and its small dimensions make it suitable for operation in the cramped conditions of modern cities.
The crane installation is driven by two axial-piston hydraulic pumps, which are driven by the engine of the base vehicle through a gearbox and an additional power take-off. Crane mechanisms have an individual drive with independent control from hydraulic motors and hydraulic cylinders. The hydraulic system of the crane installation provides smooth control of all mechanisms with a wide range of speed control of working operations, as well as the possibility of simultaneously combining several crane operations.
A three-section telescopic boom with a length of 9.7 - 21.7 m in the retracted position provides the crane with compactness and maneuverability when moving, and in the extended position - an extensive working area and a large height of cargo movement during operation.
Additional equipment of the boom with a lattice jib 9 m long allows for the largest service area and the size of the under-boom space among similar models of 25 ton cranes. The transfer of the jib from the transport position to the working position and back is carried out manually without the use of additional lifting equipment.
The possibility of telescoping the boom with a load on the hook allows the crane to perform special tasks: install loads in hard-to-reach places, carry them among mounted structures. For the convenience of working in cramped conditions, a mode of work with loads is provided with the installation of a crane on supports with the beams of outriggers retracted.
The safe operation of the Galician 25 tons is ensured by a set of instruments and devices, including a microprocessor-based load limiter with digital indication of operating parameters on the display in the driver's cab. The device automatically protects the crane from overload and overturning, is equipped with a crane coordinate protection system necessary for working in cramped conditions, has a built-in telemetric memory unit (“black box”) and a crane protection module against hazardous voltage (MZON) for operation near power lines.
Specifications of truck crane Galichanin 25t KS-55713-5
Maximum load moment, t/m 80
Maximum load capacity, t / reach, m 25 / 3.2
Boom length, m 9.7 - 21.7
Gooseneck length, m 9
Maximum hook lifting height, m
– with main boom 21.7 m 21.9
– with main boom 21.7 m and jib 9 m 30.0
Max. hook lowering depth by boom 9.7 m at reach 5.0 m, m 12
Mass of cargo at which extension of boom sections is allowed, t 4.0
Load lifting-lowering speed, m/min
– nominal (with a load weighing up to 25.0 t) 5
- increased (with a load weighing up to 6.0 tons) 12
- maximum (multiplicity of chain hoist 1) 96
Load landing speed, m/min no more than 0.3
Turning part rotation speed, rpm from 0.15 to 1.4
Crane travel speed under its own power, km/h up to 80
Support contour size along x across the chassis axis, m
- with extended beams of outriggers 4.2 x 5.6
- with retracted beams of outriggers 4.2 x 2.28
Crane weight in transport position, t 20.5
The wheel formula of the base car is 6 x 4
Base car engine: diesel
– model Kamaz-740
– power, hp 300
Crane dimensions in transport position, m (length x width x height) 12 x 2.5 x 3.6
Operating temperature, deg. C from -40 to +40
Galician 25 tons can be purchased on lease and credit.