Silver vesta on 17 discs. Lack of rims for Vesta! ZR investigation

In 2016, AvtoVAZ announced the creation Lada Vesta And Lada Xray in exclusive editions. The first cars were presented at the auto show Lada "Exclusive". The innovation of the models is 17-inch wheels. To date, such wheels are already being actively installed on Lada Xray, but Vesta is still content with only 16 inches.

In the light of these events, a reasonable question arises: how will an increase in the diameter of the wheel affect the suspension of the car? AvtoVAZ does not answer this question. Let's try to figure it out on our own.

The maximum allowable wheel size for Lada Vesta is 195/55 R16.
Vesta was presented at the motor show with Hankook tires 225/50. Presumably the size of the wheels of Vesta Exclusive will be 205/50.

As a rule, increasing the size of the disk has a positive effect on manageability. This happens due to a decrease in the compliance of the wheel to the side. Also, the volume of the braking mechanism is increased.
By increasing the diameter of the disc on Vesta, the engineers, most likely, wanted to bring the “sharpness” to the control system.

It should be remembered that with increasing mass rims dynamics is lost. If the dimensional changes are insignificant, as in our case, then the consequences are almost imperceptible.

However, how will the suspension be changed in the new version of Vesta?

Now Vesta's suspension is designed in such a way as to balance its driving performance. This greatly affects the smoothness of the car and its handling.

Thanks for subscribing!

Of course, everyone knows that an increase in the diameter of the disk is not always accompanied by an increase in the wheel. Sometimes low-profile tires are put on a large diameter disc. In this case, only the appearance of the car changes, and, in part, handling. However, there is a significant minus - uneven roads. Any hole or bump will lead to damage.

Consider the reverse situation - with an increase in size rim the wheel itself also increases. In this case, the car will accelerate and brake more slowly, but the maximum speed may increase slightly.

A large disc diameter does not always mean a lot of weight. Here you need to look at the whole wheel as a whole. However, the weight of a 17-inch wheel on the new Vesta will be slightly more than a 16-inch. We hardly notice this on the suspension of a car. Basically, you can feel the changes on a bad road.

The exterior style depends not only on the type of body color, some tuned elements, but also on the appearance of the wheels, and in particular, the disks. However, the selection of these components should be approached not only from the point of view of aesthetic values, but also the compliance of the size with the factory requirements of the VAZ Vesta Sedan 1.6 2015, as well as indicators performance characteristics. In the latter case, against the background of stamping, light-alloy metal products win to a large extent. However, financially, not every motorist can afford them.

More about the presented assortment

Regarding forged products alloy wheels in Moscow are inexpensive designs, but they are more expensive for motorists compared to steel rims. However, they are in great demand due to the possibilities of casting technology to produce real masterpieces in the style of light alloy products. Lightweight structures can become the main highlight of the exterior of the VAZ Vesta Sedan 1.6 2015. They provide decent corrosion resistance, which can not be said about steel wheels, and demonstrate excellent driving performance.

Light-alloy rims are made from aluminum or titanium alloy, which are valued due to their excellent physical and chemical properties. At the same time, in terms of strength, these alloyed metals are not particularly inferior to steel. With alloy wheels, owners of the VAZ Vesta Sedan 1.6 2015 may not worry about the safety of speed performance.

In addition, alloy wheels are valued for their fuel efficiency, which is ensured by their lightweight design and low rolling resistance. In addition, they have excellent thermal conductivity, which helps prevent the possibility of overheating of the brake and running systems. This property allows drivers to feel somewhat more confident in the safety of movement. Light alloy products are balanced and have high precision geometric parameters.

Difficulties of choice

Such a wide range of drive offers, which are offered today by domestic and foreign manufacturers, create certain difficulties when buying components in Moscow. After all, sometimes brands for the same specifications products are priced differently. However, does the quality really correspond to the declared indicators?

On the site of the online store "Wheels for nothing" you can find various reviews motorists who have already managed to evaluate in practice all the advantages and disadvantages of various disks on the VAZ Vesta Sedan 1.6 2015 and make their choice. You can also consult with competent managers of our store, who can not only choose for you best option wheels in terms of quality and cost, but will also answer all your questions.

When choosing discs, it is worth noting the importance of the quality factor of the roads on which you move. If you have to overcome extreme terrain difficulties on a daily basis, then it makes sense to give preference to only budget stamped components.

If you have a limited budget, you can always buy a more affordable, but no less high-quality replica. Moreover, today many brands create copies of the original wheels, which are in no way inferior in terms of performance to “native” parts.

Why is it worth buying discs from us in Moscow?

We offer not to waste time on a long search for reliable distributors of automotive components and order wheel parts in the Wheels for Free online store. We have a wide range of disc models various kinds from trusted manufacturers. We are sure that you will be satisfied with the quality of our service and directly with the purchased goods.

A car wheel is a necessary part, which, in symbiosis with a tire, is a device that converts external energy into useful work to move the vehicle. Each car owner should have basic information about this element and know which of them are rationally suitable for the purchased Lada Vesta. Below will be presented photos of the domestic novelty on different wheels. Disks on Lada Vesta are divided into two types:

• The first type includes cast wheels, which are made by casting into a mold of a certain diameter. The most commonly used materials for creation are aluminum, magnesium, and, in rare cases, titanium alloys. After the casting process, a heat treatment session is necessary. The final appearance of the discs is obtained after mechanical cleaning and staining process. The cost of such parts is the most optimal.
• Stamped discs represent the second type. They are made from steel sheets of ST-3 format. Two halves with holes are welded and become whole. They are straightened with a sledgehammer or on a specialized machine. Such a part is heavy, but easily yields to resistance and pressure. The main disadvantages will be susceptibility to corrosion and poor balance, which can lead to unpleasant consequences when driving at high speed.

Interesting!

On the territory of the Russian Federation, aluminum plants in Krasnoyarsk and Sayanogorsk, as well as the largest titanium processing concern, which bears the abbreviation VSMPO, are engaged in the production of wheel parts. The first place in terms of quality is occupied by Germany, Italy and the USA.

Effect on car tire and wheel size

Disks on Vesta cause a specific action for the manifestation of certain categories:

• Increasing the diameter and width of the rim, as well as the width of the tire, greatly improves the overall appearance. It improves traction and steering precision.
• The driver will clearly feel discomfort if he moves on smaller discs than were installed. This disadvantage is compensated by the expansion of the bus itself.
• Noise from the road does not depend on changing the size of the wheels. However, as the width of the rim and tire increases, fuel consumption on any surface increases.

If you look at the photo of Lada Vesta on 17 discs, you can immediately note the addition of courageous dynamism and unsurpassed style to the image. Accordingly, tires of size 17 must also be purchased here. One such automobile "shoes" will cost 5,000 rubles. And a product from a foreign workshop with an exclusive style can cost a lot of money (14-16 thousand rubles).

Photos of Lada Vesta on 18 discs were found online immediately after the demonstration of the concept car in 2015 at an automobile exhibition in Moscow. This volume of casting inspires tremendous respect for the product, as it gives the impression that the wheels are the most important part.

On a note!

The eighteenth disk element and the R17 wheel are not installed for the Lada Vesta sedan at the factory, but the owner has the right to select and mount them to give an unusual look. It is likely that such “shoes” will appear on a sports car or SUV from a domestic concern.

Wheels from the manufacturer and bought by the owner

For the Lada Vesta sedan, there are r15 wheels and r16 wheels. Stamped wheels are mounted only for the first option. They are installed on the cheapest modifications of the novelty from AvtoVAZ. Cast (r15 and r16) are available for more advanced and expensive trim levels "Comfort" and "Lux". The photographs clearly show the difference between these elements. The vehicle owner's manual provides useful information about the wheel parts on the chassis axle.

• Alloy wheels 15 radius on Lada Vesta, installed by the factory manufacturer, are equipped with a load capacity index of 560 kg (not to be confused with capacity). The tire pressure at full and partial load is 0.21 and 0.22 MPa, respectively. These parts are mounted today on all configurations of a four-door sedan from the Togliatti concern. All these indicators equally apply to the "stamp" disks (radius fifteen).
• Alloy wheels 16 radius on Lada Vesta, delivered on the conveyor of the plant, have a large load capacity index - 615 kg. Tire pressure is similar - 0.21 / 0.22.

On a note!

If the owner decides to change the wheels on his car, you need to understand that 15-inch wheels have a limit in the index. top speed- 190 km / h. For R16, this figure rises to 210 km / h. Winter tires do not allow you to accelerate the vehicle beyond the limit of 160 km / h. Failure to follow instructions may result in an accident.

Balancing as a prerequisite for safety

This procedure, carried out successfully, is intended to be a guarantee of getting rid of the beating of the multi-wheel while driving at high speed and the subsequent crash of the car. In addition to the steering wheel, shock absorbers and other elements of the chassis will fail in succession.

The balancing procedure is required at least once a year. It is required when changing tires. The main cause of wheel wobbling is rubber wear and subsequent molding deformations. For the operation, you should contact the tire service.

The combination of the Lada Vesta body palette and wheel elements

Today, very often they are engaged in decorating a car by combining contrasts and different shades in design. The manufacturer went to meet lovers of aesthetics and began to produce castings in a variety of colors.

To make the wheels on the white Lada Vesta look good, it is recommended to buy wheels in a contrasting black tone. This interesting solution is easy to separate undercarriage from the body itself. Wheels on a black Lada Vesta should become white in priority, which will brightly and stylishly make your vehicle stand out from a huge number of cars on the highway and in the city.

Where to buy the part

Casting and "stamping" of ordinary diameter (R15 / R16) is sold on specialized Internet sites, as well as in the salons of the official supplier of spare parts from AvtoVAZ. Stamped discs for Lada Vesta are the cheapest in the range. Their price starts about 1300 rubles. You can buy alloy wheels for Lada Vesta in stores for 2,500 rubles. The range of this product on the shelves is huge, which will allow each owner to find a suitable wheel for his car.

R18 wheels, like r17 wheels, have a higher cost (from 5,000 rubles) and low-profile tires, which are very sensitive to road irregularities. They are mounted on the axis of the chassis to visually highlight the attractive part of the car.

Lada Vesta on casting from Lada on stamped wheels is distinguished by the best design and quality, so the consumer has a large field of choice. Which of them to buy, the potential owner decides. In addition, it is possible to first view the necessary photos, and then observe the image of the product live.

To date, various discs for Lada Vesta are on the market. The main differences between them are the materials from which they are made, methods of manufacture and fastening, dimensions. To choose the right components for the car, you should know their sizes, presented in the table below.

T - index of permissible speed within 190 km / h;

H - index of permissible speed within 210 km / h;

ET - rim offset, indicating the distance from the mating surface of the disk to the middle of its rim;

partial load - the presence of three adults in the cabin, without cargo in the trunk;

full load - the presence of more than three adults in the cabin, or the presence of three adults in the cabin and luggage weighing 50 kg or more (depending on the capacity of the luggage compartment).

The wheel is attached to the hub of the car using four bolts through the holes on the disk. It has four holes, the centers of which are located at a diameter of 100 mm.

The simplest and cheap option These are stamped steel wheels for Lada Vesta. They are made by stamping a mold. The external differences of the parts depend on the characteristics of the stamp, in accordance with its forms, the product acquires its final form. The main advantage of stamping is strength and resistance to external influences: abrasions, shocks, scratches.

Steel r15 discs are provided by the manufacturer when buying a car in the basic configuration. Recommended tire sizes are 175/70 R15. You can buy stampings in many service centers and stores by pre-ordering them on the store's website, where photos and prices are presented. The retail price in Moscow starts from 1,300 rubles apiece and can reach 2,500 rubles.

When buying discs, you should first clarify whether fasteners are included in the purchase price. Sometimes fasteners need to be purchased separately.

Popular alloy wheels on Lada Vesta are distinguished by a wide choice of design and diameter. They are made from a special alloy. In addition to the base metal aluminum, the alloy contains magnesium, strontium and titanium additives. The casting process takes place under high pressure, which contributes to the rapid solidification of the workpiece. With the help of computer modeling and milling, the part gets its final shape.

Multi-level manufacturing process alloy wheels explains their high cost. They are lighter in weight, but have less resistance to mechanical damage.

Lada Vesta for casting is presented by the manufacturer in two versions:

• r15 rollers are recommended for 175/70 R15 and 205/60 R15 tires;
• r16 rims fit 185/60 R tires

On a note!

Alloy wheels 15 radius on Lada Vesta are provided when buying a car in the luxury package. For a fee as additional equipment alloy wheels 16 radius can be installed on Lada Vesta.

You can buy alloy wheels for Lada Vesta in specialized centers and online stores, on whose websites photos of goods are presented. average price for casting with a radius of R15 2500 - 4000 rubles, depending on the manufacturer and design. 16-inch rollers will cost the car owner more - from 3,500 to 6,000 rubles apiece.

Alternative wheel sizes

In pursuit of beauty and the unusual appearance owners of Lada Vesta install rollers of the seventeenth and eighteenth radii. They provide for the presence of low-profile rubber, which is very sensitive to the slightest bumps in the road, which makes driving a car less comfortable.

Wheels r17

Quite often there are West cars with wheels with a radius of R17. They look noticeably larger than the standard fifteen inches. Recommended tire sizes for this type of casting are 175/55 R17, 195/50 R17. External features presented in the photo Lada Vesta on 17 discs. You can buy such shoes for cars for 5,000 rubles apiece, foreign-made goods with an exclusive design will cost 15-17 thousand.

Rims r18

For the first time, rollers of this size were presented at the Lada Vesta concept with 235/45 tires. Photo Lada Vesta on 18 discs clearly demonstrates the sporty design and dynamics of the car. Casting R18 is much more expensive than its "younger brothers" - from 9,000 rubles apiece.

Recently, it has become very popular to combine contrasting colors in car design. This fashion trend contributed to the release of rollers in different color schemes. On the Internet, you can find many photos with various color combinations for the car body and disc rim.

Disks on a white Lada Vesta are recommended to be set in contrasting black. Black casting favorably looks against the background of a white body. By the same principle, you can select disks on. White rollers will stand out brightly and attract the attention of others. The classic silver molding is suitable for cars of any color and is a universal option.

Among the numerous design innovations, the attention is drawn to the wheels on Vesta with a bright red edging along the edge of the rim and on the spokes. They are suitable for any color of the car body, but it is preferable to put them on a red car. This combination gives the car sporty look and unique personality. Even in dense city traffic, the car will stand out from the general flow and attract the views of others.

What affects the size of tires and wheels

Increasing the size of tires and rims will affect the operation of Lada Vesta in the following way:

• Increasing the disc diameter has a positive effect on steering quality, road holding, but reduces the level of comfort on rough roads.
• Increasing the disc width will also improve steering and road retention, but will increase fuel consumption.
• Increasing the tire width will also have a positive effect on handling, including on rough roads, and improve traction (in dry weather). At the same time, gas mileage and tire wear will increase, and hydroplaning resistance will suffer. The noise level will increase.

Good afternoon, dear zarulevtsy!I want to throw a current topic for the article. I am the owner of Lada Vesta SW Cross, and now the purchase is relevant for me winter tires on disks. However, it turned out that AVTOVAZ used a non-standard wheel with an offset of 43 and requires only it to be used in order to avoid voiding the warranty. The official disc costs cosmic 7.5 thousand, possible replacement only one - for 6.5 thousand, and even the manufacturer has only 1 (one) disk (consider that there is no replacement).Thus, the plant imposes the purchase of its unique disk at a clearly inflated price. Why not draw the public's attention to this and ask the factory for comments? At the very least, the factory could have allowed other replacement options. Judging by the forums, people put the 15th and 16th wheels at the risk of a guarantee, because the imposed option is corny twice as expensive.With all respect, Andrew.

Dear Andrey! We have tried to answer your questions from all possible positions.

Officially

Any manufacturer, not only AvtoVAZ, will require the use of only those that are prescribed in the operating instructions. On them, the car passed factory tests and certification. How he will behave on "shoes" with other parameters, the manufacturer does not know, and he cannot take responsibility for such a replacement.

To confirm this obvious, in general, information, I nevertheless contacted the AVTOVAZ press service and called incognito on hotline Frets. Both sources were unanimous: only 17-inch tires and wheels with the parameters prescribed in the operating instructions are allowed on the sedan and station wagon. Other options will be considered as a reason for refusing to warranty repair chassis.

Sanctions

You can pay not only by refusing free repairs. If tires not approved by the factory are noticed on the road by a traffic police inspector, he has the right to draw up a report on the non-compliance of the car with the requirements technical regulation, clause 5.1 of which reads: “Vehicles must be equipped with tires in accordance with the manufacturers’ operational documentation Vehicle". And this is a reason to terminate the registration if the malfunction is not corrected.

Wheel marking is usually applied to the inner surface. If you put Vesta Cross on the same 17-inch wheels, but with different offset, width and diameter parameters central hole, of course, the inspector will not be able to assess compliance right on the road. But another diameter is already obvious, and it will tell you on the tire.

A diameter other than the seventeenth will also put an end to the possibilities. If you completely exaggerate, extremely unpleasant consequences can arise in the event of an accident with a serious outcome. After these, they often appoint a lot of examinations and find out all the details. Non-standard wheels will pop up, and who knows how the investigators will regard it. But this is a theory.

Reality

Real life, as usual, has some differences. I called several official Lada dealers in Moscow and, introducing myself as the owner of the SW Cross station wagon, asked for advice on an alternative to my native 17-inch “shoes”. The answers were like a blueprint. The parts department managers saw no problem with fitting 16-inch wheels and were willing to offer options.

To the question in the forehead "What about the guarantee?" shaded and switched to the appropriate specialist. And already a predictable answer sounded from the warranty master: the wheels will get up, but the appearance with them at the service will be a reason to refuse free suspension repairs. However, everyone made it clear that this would not happen necessarily. Would you take their word for it?

Of course, you can guess maintenance trips for the season, when your Vesta is shod in factory wheels. But the very fact that dealers are wooing dimensions that are not approved by the factory is outrageous. Someone will buy them without asking any questions! And then in the same technical center, to his surprise, he will receive a denial of a guarantee.

Should AvtoVAZ be blamed?

First of all, the wording "it turned out" in the reader's question is incomprehensible. The dimensions of tires and wheels allowed by the manufacturer are indicated in the instruction manual, which is posted on the official website in the public domain. If spending on car consumables is so important to the future owner, it is wise to conduct a price analysis before buying a car.

It is worth recognizing that AVTOVAZ was really greedy with the price of the original 17-inch wheel (about 7,500 rubles). After going through a dozen of the largest wheel sites, I really found only one perfect fit - KiK Flanker. It is cheaper by a thousand rubles, which saves 4,000 rubles per set. Which, in my opinion, is not so little.

In the end, there is no obligation to start a complete winter kit. Are the wheels too expensive? Buy only tires. For the money that the Lada dealer asks for one disc, you can change the whole car three or four times.

And speaking quite frankly, AVTOVAZ is by no means alone in its desire to make some money. Such a "divorce" for extra money, if you search, can be found in almost any car! And the case with Vesta Cross is not the worst yet: for an attentive buyer, it is obvious even before purchase.

If you do not go far from the topic of the chassis, I offhand recall two examples. On the french cars for a long time, alloy wheels without a center hole were used. them on a standard tire changer is not possible. I had to look for a workshop with rare equipment. Someone in the regions - I'm sure! there was only one way to official dealer with its queues and draconian prices. And for non-original racks were not produced. And this despite the fact that last generation C5, their "snot" and knocks could not be corrected for years, and the owners of the cars changed several sets in a row.

Finally, a little hint: write complaints and wishes if something does not suit you. Only not to the magazine "Behind the wheel", but directly to the manufacturer. In recent years, AVTOVAZ has repeatedly demonstrated that it listens to customers. Perhaps, when the number of hits reaches a critical volume, 16-inch tires and wheels will be certified for Vesta in the Cross version.

Lack of rims for Vesta! ZR investigation