Correct selection wheels and tires on a vehicle should involve the selection of products in accordance with the requirements of the manufacturer. Deviation from certain standards may cause the technical impossibility of installing a disc or tire, as well as a violation of safety rules. In the regulatory documentation from automakers, there are recommendations on the selection of wheels for a particular model, taking into account the parameters of wheel bolt pattern, etc.
Selection for fifth models
Skoda Octavia A5 models, depending on the configuration, were equipped with steel or light alloy wheels of the same bolt pattern. Cheaper modifications were completed with steel, or so-called stamped products. The manufacturer provided for the permissible characteristics of the disc for A5 models, which were produced from 1996 to 2004, namely in terms of hub diameter - 57.1 mm (this indicator is marked with DIA coding), the diameter of the product itself - 15, 16 and R17, departure - from 30 to 46 mm (ET). At the same time, the number of holes for fasteners is 5 pieces with a diameter of the conditional circle on which they are located, 100 mm. The manufacturer, when selecting products by width, recommended choosing between indicators in the range of 6 - 7.5 inches. To fasten the product to the vehicle hub, M14x1.5 type bolts are used. The location parameters and technical characteristics of the bolts, as well as their number, are called bolt pattern.
Skoda Octavia A5 models, which were produced between 2004 and 2008, had slightly different disk sizes. So, the diameter of the location of the elements for fastening the product to the hub has increased to 112 mm, and the manufacturer provides for the installation of disks with a diameter of 15,16,17 and 18 inches on the car. The departure indicator (ET) has also changed and is 31-50 mm.
Regarding the selection of rubber tires, one should, of course, take into account the size of the main disk. So, the most popular and in demand are tires with data 195 for 65 R15, 205 for 60 R15 91 h-v, 205 for 65 R16 91 h-v-W and 225 for 45 R17 91 h-W. At the same time, products that have proven themselves from the best side are produced under such brands as Pirelli, Goodyear, Nokian, Michelin and many others. The correct selection of products for a specific period of operation is also important, as well as depending on the climate of the area where the vehicle will mainly be operated.
Summing up the results of the selection of cast or stamped products for Skoda Octavia A5 cars, including rubber, it is worth giving an example of the optimal combinations of elements of an automobile wheel in the table:
Selection for the seventh models
The choice of products on the Skoda Octavia A7 model is much more diverse, unlike the previous model. So, depending on the modification (regular or Tour model), as well as on the year of manufacture of the model, the data of tires and wheels may differ significantly. The simplest stamped products are installed on the basic equipment of cars Skoda Octavia A7 and Tour. This part code is 5Q060102703C.
The bolt patterns for the Skoda Octavia A7 models have the following data - 5 to 112. In this case, the number "5" indicates the number of main bolts that are used when attaching the element to the vehicle's hub, and "112" indicates the diameter of the circle on which the holes for these mounting bolts. In the complex, this indicator is called bolt pattern. The third generation Skoda Octavia A7 differs from the representatives of the second only in the width and offset of the light-alloy or cast wheel components.
From the factory, models are equipped with sizes of 15 inches, 16 and 17. So, the data for the 15th radius is 6.0J PCD 5 for 112 ET 47, for the 16th - 6.5J PCD 5 for 112 ET 46-48 (57.1) and for 17 7.0J PCD 5 on 112 ET 43.
The bolts used in the A7 have a standard size for most representatives of the Czech automaker - M14 by 1.5.
Choice of cast original elements for Skoda Octavia models of the A7 type, including the A7 Tour models, deserves special attention. So, depending on the selected configuration of the A7 or as additional option You have the option to choose from a variety of styles. As original cast elements on the Skoda Octavia A7 model, including the Tour model, types such as Minoris, Denom, Ilias, Gemini, which have a standard bolt pattern, are installed. Among those listed, it is worth highlighting the Denom and Gemini models, which are also suitable for the A5 model, and the most popular for the A7 models is the 16th size.
Cast Denoms are rated for standard bolt patterns and are 7.0J by 17" (ET 49). On the Denom type, however, as well as on Minoris, Ilias and Gemini, the manufacturer provides for the possibility of installing anti-slip chains when operating the car in the winter season. The Denom model, according to the results of various tests, has demonstrated its best side and, not without reason, enjoys a high level of demand among owners Skoda cars Octavia A7. The Denom cast elements feature a silver finish, five spokes and a unique design. Depending on the configuration of the described vehicles, it is possible to install R18 wheels. So, for diameter R18, cast elements such as Turini, Alaris and Golus are used. All these R18 models differ in performance and appearance. It is worth noting that each of the types of light alloy elements Octavia models A7 has its own unique code. For example, the Denom 17 model is marked with the code 5E0601025D8Z8, and the Turini R18 can be in several color schemes. The article of one of the most popular elements is R18 5J0071496M 7ZS. Elements of the R18 type significantly affect the appearance of the models, giving a sporty style and aggressiveness.
Selection of different tire sizes on the Octavia A7 model is also carried out depending on the alloy wheel elements used. So, for a radius of 15 inches, tires 195 to 65 are suitable, for a radius of R16, 205 to 55 are optimal, and for a radius of 17 - 225 to 45.
Car owners make a choice mainly considering the decorative component of the part. In this case, the selection should be made, taking into account all of the above data. The most popular and sought-after tires for the Octavia A7 models are Michelin Energy Saver, Continental ContiPremiumContact or Dunlop SP Sport FestResponse, while alloys come with a 16" radius.
Summing up the description of the parts that can be used in the A7 models, the information should be summarized in the table below.
In this case, the symbol "J" indicates the shape of the edge of the rim, and "R" the radial design of the rubber tire (for example, R with a value of 16). The hub hole in the seventh models is no different from the previous generation.
Using the automatic selection of tires and wheels for the car Skoda Octavia, you can avoid many problems related to their compatibility and compliance with the recommendations of car manufacturers. After all, they have a huge impact on a significant part of the operational properties. vehicle, first of all, on handling, fuel efficiency and dynamic qualities. In addition, tires and wheel disks in modern car are one of the elements active safety. That is why their choice should be approached as responsibly as possible, that is, with knowledge of a number of parameters of these components.
Unfortunately, or, conversely, fortunately, a significant part of motorists prefer not to study technical device own car thoroughly. Fully automatic system selection in this case is almost the only way to avoid the wrong choice when buying tires and rims. And it is very wide, which is due to the diversity of the range of such products presented in the Mosavtoshina online store.
You are lucky enough to become the owner of Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013 in Moscow and you are looking for high-quality and inexpensive tires for your vehicle? We invite you not to leave the online store "Wheels for nothing" and consider the options that we can offer. Our range of tires is more than just a catalog section. Through a long analysis and monitoring of needs Skoda owners Octavia Liftback 1.6 MPI (1Z) 2004-2013 we have formed a list of functional and productive wheels from various domestic and foreign brands at an affordable price.
A huge range of safe and high-strength Winter tires, wear-resistant summer tires, universal all-weather tires. Your choice of components of European, Asian and American production. All presented goods are certified and have a factory quality guarantee. Also in the catalog you can pick up models identical to the original wheels. Your car deserves comfort, quietness, reliability and excellent driving performance. Both cheap tires and premium class tires in Moscow can provide this list of properties. The tread of the original summer tires on the Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013 is endowed with minimalism, able to give acoustic comfort and smooth running. However, sooner or later it wears out or colds come, and there is a need to change the seasonality of the wheels.
Selection of the exact tire size Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013
Many tires for Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013 by appearance very similar to each other. It would seem that the tread pattern is the same, but the degree of its complexity is individual for each model. The same variant may have hundreds of subspecies, so choose summer tires, the price of which fits almost any budget, especially carefully, taking into account the smallest details. When buying new tires, consider:
Reliable summer tires You can buy a Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013 in Moscow right now, after making sure that the model you have chosen fully meets all the requirements of the car.
Winter tires
In the cold season, it is important that tires have high traction and grip properties with snowy and icy surfaces. In addition, the list of their characteristics should include:
- high strength;
- excellent cross;
- excellent resistance to slashing;
- durability;
- reinforced frame;
- optimal grip and braking efficiency.
You can also save and buy all season wheels for Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013. However, remember that they are only suitable for operation in regions with warm winters. In addition, in terms of performance, all-season tires are much inferior to winter and summer tires.
Quick sale of tires for Skoda Octavia Liftback 1.6 MPI (1Z) 2004-2013 in the Wheels for Free online store
The best competent specialists worked on the development of our online portal. Therefore, you are presented with a comfortable virtual version of the trading floor, where from model to model is a few clicks away.
For the entire range Skoda tires Octavia Liftback 1.6 MPI (1Z) 2004-2013 presents current democratic prices, as we work directly with manufacturers. You can order wheels of any season without leaving your home. What else could be easier?
Skoda Octavia A5- car brand, which is part of the concern "Volkswagen Group". The model was produced from 2004 to 2013, after which it was replaced by a newer modification.
Release updated version in 2009 did not affect the change in the size of tires, wheels. They are also interchangeable with each other.
What original discs are installed by default on the Skoda Octavia A5
| Common parameters | The size |
|---|---|
| Tire R15 | 195/65R15 |
| --/-- | 205/60 R15 |
| Bolt | 14*1.5 |
| PCD | 5*112 |
| Dia | 57.1 mm |
| Rim | 6Jx15 5/112 ET 47 |
| --/-- | 6.5Jx ET 38 |
| --/-- | 7JxET 35 |
| Rim diameter | 14 / 15 |
| Construction type | R - radial |
Any other dimensions other than the above are considered non-original (non-standard). Installation of parts, assemblies under the personal responsibility of the owner, as this leads to a change in a number of specifications, namely:
- Controllability;
- Road grip;
- Sharpness and responsiveness of the steering wheel;
- Decreased/increased hydroplaning;
- Comfort of movement;
- Noise level;
- Fuel consumption in the combined cycle;
- Tread wear rate.
Permissible sizes of disks, tires, for Skoda Octavia A5
| Name | Wheel / tire size |
|---|---|
| Rim | 6Jx16 5/112 ET 50 |
| --/-- | 6.5J (ET50) |
| --/-- | 7Jx (ET 38) |
| --/-- | 7Jx (ET 38) |
| --/-- | 7.5Jx (ET 35) |
| --/-- | 7.5Jx185 (ET38) |
| --/-- | 8Jx18 5 (ET 35) |
| --/-- | 8Jx195 (ET 38) |
| freelance tires | 215/65 R16 |
| --/-- | 205/50R16 |
| --/-- | 215/55 R17 |
| --/-- | 2125/50 R18 |
| --/-- | 225/45 R19 |
| Rim diameter | 14 / 15 / 16 / 17 / 18 / 19 /20 |
| Construction type | R - radial |
- During maintenance, check the geometry, wheel balance on a special diagnostic stand. If deviations are found, restore the integrity of the structure;
- In the event of cracks, dents on the rim, immediately contact the service station for prevention;
- Avoid bumps in the road at high and medium speeds. Regardless of the material, workmanship, the disk will be deformed, the tightness will be broken;
- Keep an eye on the pressure in the tires, it should not be lower / higher than recommended by the manufacturer. In case of deviation pump up;
- Timely switch to summer / winter mode. This means that in summer the pressure in the tire is higher by 0.15 atm, in winter it is lower by the same amount. The parameters are indicated in the vehicle operating instructions;
- Tighten the nuts on the rim with a torque wrench. Excessive tightening contributes to the breakage of the studs, weak - an emergency, unscrewing the wheel.
In dry, sunny weather, cast aluminum wheels are the least susceptible to damaging external influences. But in slush, ice, when the road is strewn with various chemicals, the rim is most susceptible to corrosion. This provokes peeling of the paint, the destruction of the molecular composition.
Wash the wheels as they get dirty. Since it is unlikely that it will be possible to wash it with a rag, use high-pressure compressors. Equipment of this class is available at many service stations, workshops, service centers.
Systematic polishing allows you to get rid of scratches, scuffs. Pre-clean the wheel of dirt, dry thoroughly, and then treat with a chemical. Wipe several times with a microfiber cloth.
Store the wheels in a raised position without touching each other. Pre-clean them, dry them, wrap them in cellophane.
Some motorists practice to apply an aerosol to the surface before conservation. However, this is a purely personal decision of the owner.
Deciphering the tire markings on the Skoda Octavia A5
Factory-made tires have the following markings on their sidewalls:
- Width;
- height;
- Rim diameter;
- Construction type designation;
- Load index;
- Speed index;
- Reinforcement of sidewalls, lamellas, if required by technical specifications;
- Name of the country of origin;
- DOT - encrypted code of the manufacturer according to the international specification;
- Designation outer side for asymmetric tires;
- M&S - marking indicating the purpose of rubber for use on slippery surfaces, in slush, on loose snow;
- An eight-digit code indicating compliance with the ESE standard;
- Tire type: chamber, tubeless;
- Construction detail;
- Name of the brand, company;
- Model;
- Data on the permissible maximum load and pressure.
Some features of the marking of American tires
With the European alphanumeric designation of rubber, disks, the driver encounters much more often than with the American one. When choosing and buying consumables, it is often difficult to understand the size, dimensions, diameter, thickness, height.
- "P" - exclusively for the passenger class;
- "LT" - category "C", commercial vehicles;
- 5 R16: typical designation American tire, disk.
Where, 32 is the outside diameter in inches. 11.5 - width in inches, R - radial design, 16 - inside diameter (inch).
- XL on sidewalls: Reinforced tire with nylon inserts to prevent damage while riding;
- Extra Load: index of maximum load. For example, 92 is equal to 680 kg. Exceeding the specified boundary range is not desirable, as it can lead to deformation, rupture of the disk, tire;
- All Season: the designation familiar to us from the European class, denoting all-weather, operation in any weather;
- * (snowflake): for the use of rubber at low temperatures, on snow, ice, slippery surfaces. The absence of a pictogram allows you to use the tire as a summer tire;
- Pictogram (umbrella): for wet surfaces;
- Outside: asymmetric tires. It is important to consider this factor during installation. Incorrect installation leads to deformation of the tread, its rapid wear, damage to the sipes;
- RSC (RunFlat System Component): the ability to continue driving the car with maximum speed 80 km / h with a flat tire;
- Rotation: The direction of the tread. Consider this factor when installing. The arrow always points in the "forward" direction;
- Tubeless: tubed / tubeless type;
- Reinforced: rubber layering in manufacturing;
- Temperature: heat resistance class, elasticity at high temperatures;
- Treadwear: recommended mileage;
- TWI (Tread Wear Indiration): tire wear indicator. As a rule, it is indicated by red, yellow, green markers. Green - safe, yellow - acceptable, red - replacement;
- DOT: manufacturer code.
Subject to a moderate driving style, compliance with speed limits, the average tire life is 70,000 km. Cast, aluminum wheels nurse up to 150,000 km.
Installation of freelance equipment, mechanisms is not always expedient and effective. Get advice from experts first, read the requirements of the instruction manual. The book indicates the maximum permissible sizes of tires, disks.
During the factory warranty period technical means interfering with the operation of nodes, assemblies is not desirable. In case of emergency, use the services of certified service stations, workshops, ateliers.
In the process of manufacturing disk structures, leading manufacturers take into account the individual needs of customers. Modern design products are not just another obligatory element of the car, but its real decoration. Qualified specialists work on the creation of new design solutions, who translate their extraordinary ideas into reality. In the production of high-quality structures, great attention is paid not only to performance, design, but also to quality. Engineers take into account all the nuances to ensure maximum safety on the roads when driving in various climatic conditions.
Certified product for Skoda Octavia A5 cars has successfully passed all possible tests and tests. After testing the designs at the factory, specialists produce products for sale with official guarantee. To quickly select a product, you must first indicate the year of manufacture of the vehicle, and then the engine size. After that, the car owner must decide on the size of the structure. Guided by these indicators, you can easily select the appropriate components. The following options are on the market today:
Rims for Skoda Octavia A5
- factory equipment (original tires);
- alternative options (replicas);
- tuning models.
Alloy wheels for the Skoda Octavia A5 are distinguished by a variety of design solutions, which allows the car owner to choose a kit based on the exterior of a particular car. An important advantage of the latest developments is low weight. Thanks to this indicator, dynamics are significantly improved and rolling resistance is reduced, which has a positive effect on fuel economy.
Note!
When choosing products, it is important to know that the sizes must fully comply with the values \u200b\u200bspecified in the service instructions. Otherwise, even a specialist will not be able to put the wheel on the hub, and if it does, it can cling to the chassis elements during rotation.
How to choose products
Choice of designs for Skoda Octavia A5
The disks on the Octavia A5 are quite powerful developments. These products are chosen for their own safety. They are equipped with an improved version brake system. However, it should be remembered that the pads must be changed in time as soon as they wear out a little. But unfortunately, many people forget about changing discs depending on the season.
Original wheels for the Skoda Octavia A5 have the following characteristics:
- Thickness of a forward brake disk - 25 mm.
- The minimum thickness of the front structure is 22 mm.
- Thickness of a back brake product - 10 mm.
- The minimum thickness of the rear product is 8 mm.
Good quality wheels on the Octavia A5 are quite suitable for city driving or going out of town. Price policy similar designs, in contrast to the cost of disks for other cars in the same class, is relatively low.
Along with original developments, the domestic market is represented big choice alternative manufacturers. In this option, the main thing is to decide on the desired criteria. So, the most popular replacement for the original designs are models from the manufacturer ATE.
This alternative is the most economical. Products of this series are in no way inferior in quality to the original designs. The original development can be installed on your own car if the driver prefers to drive at low speed.
Since most of the braking load is on the front axle, ATE has developed structures for it with improved and more durable characteristics. These discs are cheaper than the original ones. In the production of new developments at the plant, high-quality materials and innovative technologies are used. As a result, braking performance has been improved. In addition, the discs endure overheating.
Sizes and parameters of rims for Skoda Octavia Tour A5
Dimensions of auto products
Most motorists who plan to change shoes or change wheels and tires to other sizes are wondering what size wheels fit the Skoda Octavia A5.
When choosing a wheel or alloy wheel, you need to pay attention standard sizes(diameter, product width, offset, hub hole, number of bolt holes and their distance), as well as the characteristics of the vehicle as a whole.
Note!
Non-standard sizes of tires or disks lead to changes in the characteristics of the vehicle for the worse.
| Disks | Tires |
| 6J x 15 ET47 5×112 DIA57.1 | 195/65 R15 91H/V |
| 6.5J x 15 ET50 5×112 DIA57.1 | 205/60 R15 91H/V |
| 6.5J x 16 ET50 5×112 DIA57.1 | 205/55 R16 91H/V/W |
| 7J x 17 ET54 5×112 DIA57.1 | 225/45 R17 91W |
Options
Main parameters of the product
In addition to the material and method of production of the structure, you should ask about the mounting width of the rim, as well as the bore diameter. It is necessary to determine how these indicators are indicated:
- J - width in inches;
- 15, 16, 17 - diameter in inches;
- 5×112 - the number of bolts (5) and the diameter of the circle on which the mounting holes are located - PCD in mm (112);
- ET - reach in mm;
- DIA - diameter central hole in mm.
The original Draconis 6.5J x 16 ET 50 wheel for 205/55 R16 tires looks great on all types of cars.
In appearance, it is difficult to distinguish the dimensions of the developments. They look at R17 although they have 16 dimensions. Such developments ensure safety on wet pavement. Skoda Replay SK105 6.5×16/5×112 D57.1 ET50 is a new series from the manufacturer Skoda.
Why is it important to choose original wheel designs for the Octavia A5
Installation of original wheel structures
Any owner of the Skoda Octavia A5 is thinking about replacing standard tires and wheels. You need to familiarize yourself with the factory wheel sizes determined by the manufacturer and prescribed in technical documentation. It should be noted that low-profile tires 225/45 R17 are intended primarily for sports Skoda modifications Octavia A5 RS with a powerful 200-horsepower turbo engine.
The main parameter when choosing auto disks for Skoda Octavia is the presence of mounting holes. Many also pay attention to the diameter of the central hole.
It is important to note that the parameters of the Skoda Octavia do not depend on the shape of the body (hatchback, sedan, station wagon, etc.).
On Skoda Octavia, you can install designs R15, R16, R17, R18, R19, R20 (taking into account the year of manufacture of the car and equipment).
In conclusion, it should be noted that when choosing products, it is necessary to pay attention to design, strength, size, as well as performance characteristics. Many disks on the Skoda Octavia A5 cannot be restored after damage. Therefore, it is very important to choose the type of structure in advance in order to avoid unpleasant consequences.