What is poured into the Hyundai Getz power steering. The main functions of hyundai getz gur oil

Hello. We will replace the power steering fluid with a Hyundai Getz.

The fluid needs to be changed every 40-60 thousand km. This replacement interval significantly extends the life of the pump.

Fill with fluid with PSF-3 approval.

Tool:

1. 0.5 bottle (for draining old liquid)
2. a large syringe with a tube at the end (for pumping fluid out of the tank)
3. pliers (for clamps)
4. jack
5. two supports for the body (to hang the front wheels)

Step by step replacement

1. We jack up the front of the car and install it on stands.

The front wheels must be in the air.

2. Open the lid and pump out the gur liquid from the tank. We pump it out with a syringe with a tube.

3. After pumping out all the liquid, remove the tube from the tank and lower it into the bottle that we prepared earlier.

4. Now we need to plug the fitting on the tank from which the tube was removed.

It can be done different ways I think everyone will find something in their garage. If there are no ideas at all, look at how they did it on the video.

5. An assistant with clean hands goes to turn the steering wheel into the salon. You need to turn all the way to the left and right, slightly delaying the steering wheel in extreme positions. You need to twist until you remove all the liquid into the bottle.

7. We take a new liquid and fill in almost a full tank.

8. We repeat the procedure for pumping the system. It is necessary to do as in the fifth paragraph of the work.

If you want to rinse to the ideal, pour another almost full tank and repeat the pumping.

9. Remove the plug from the tank fitting and put on the tube. Be sure to install the clamp in its place so that there are no leaks.

10. Fill the liquid almost to the top of the tank and continue pumping. Top up as fluid drains from reservoir. Thus we will pump the system.

The fluid should be between the marks on the reservoir.

It is very important to bleed the system completely, make sure that there are no air bubbles from the return line. If the system is not completely pumped, then when the engine is started, the liquid will foam and may break the tank cap.

If it happens that the liquid foams, do not panic. Stop the engine, wait a bit, and continue pumping.

To replace with flushing without fanaticism, you need one liter of fluid.

Replacing the working fluid of the power steering (GUR) is a procedure that must be performed once every 50,000 - 60,000 km of a car's run or due to the condition of the fluid. If the liquid has acquired a dark, opaque color and a characteristic burning smell, the liquid should be replaced. In the very procedure for changing the fluid on Hyundai Getz cars, like on many other cars with a power steering system, there is nothing complicated and it will take about an hour.

Recommended fluid change interval in the power steering system:
50-60 thousand kilometers

In the power steering system of Hyundai Getz cars of both generations, a fluid with a PSF-3 approval is used. Fluid with other tolerances can damage the system, in particular the power steering pump itself. Power steering fluid for other cars should be selected in accordance with the recommendations of the car manufacturer.

Power steering fluid replacement step by step

1. We hang the front of the car on stands (we tear off both front wheels from the ground, thus removing all the load from the steering);

2. Using a syringe with a small tube, we pump out the old liquid from the power steering barrel;

3. If you want to change the maximum volume of the old fluid, you need to remove the tank. It is attached with three bolts to the body.

4. Remove the clamps, disconnect the barrels, drain the remaining power steering fluid

5. We return the barrels to their place, put on the lower thick hose.

6. We lower a thin hose (“return”, comes from the radiator) into a bottle with a volume of about 0.5 liters. The vacated upper hole in the tank must be plugged, for example, with an M10 bolt

7. Rotate wheel to extreme positions, holding the steering wheel in extreme positions for 2-3 seconds. The bottle will begin to squeeze out the old fluid from the system. The volume of the old liquid will be approximately 500-600 ml .;

8. We flush the system. To do this, without assembling the system, it is necessary to pour about 200 ml into the tank. new fluid with PSF-3 approval. The flushing procedure is similar to the procedure for squeezing old fluid out of the system. We rotate the steering wheel to the extreme positions until the entire volume of the filled liquid (about 200 ml.) Comes out into the drain bottle;

9. If necessary, or if desired, you can repeat the flushing procedure. As a rule, after changing the fluid, about 400 ml remains. new fluid, from 1 liter. total volume of new fluid;

10. We put the "return" hose in place, fill in new fluid. We pump the system, adding new fluid to the tank if necessary, until air stops coming out of the “return” hose. Otherwise, when the car is started, an incompletely pumped system will foam the liquid in the tank and you will have to repeat the pumping procedure, but after waiting until the foam settles.

11. We make sure that there is no air in the power steering system, we assemble the entire system in place, remove the car from the stands.

Video instruction for replacing power steering fluid

Required Parts

• Power steering fluid - 0310000110 (yellow) or 0310000100 (red)

IMPORTANT

The duration and efficiency of the Hyundai Getz steering system depends on its condition, timely maintenance and compliance with the simplest operating rules.

The use of oil that has lost its useful properties and used up its resource leads to rapid wear and failure of power steering elements.

In force majeure situations, with a significant oil leak, the lost volume can be compensated for some time by adding automatic transmission fluid or engine oil. At the service station, this operation is carried out by experienced specialists, starting with flushing the system with special means and ending with high-quality pumping and checking the power steering.

Simultaneously with the replacement of the Hyundai Getz power steering fluid, it is necessary to change the filters in the system.

If any malfunctions occur, timely diagnose the power steering and replace the Hyundai Getz power steering oil in order to avoid serious damage.

OPERATING PRINCIPLE OF POWER STEERING

The power steering greatly simplifies the control of the vehicle, when it fails, it becomes difficult to make turns, therefore, to produce Maintenance hydraulic booster Hyundai Getz is necessary on time, ignoring the timing of the oil change can lead to serious damage to the assembly itself or the steering rack.

This mechanism significantly reduces the effort required to turn the steering wheel. Only through the use of power steering will maneuvering become easier, the driver becomes more comfortable driving the car. Virtually all modern cars there is a power steering system. The mechanism is based on a pump driven by a motor, a control valve and a dual-acting hydraulic cylinder combined with a steering rack. When the steering wheel is turned, the corresponding valve opens, fluid enters the cylinder, creating a force that easily turns the wheel. Also, in addition to the power steering, some models of Hyundai Getz cars have electric amplifiers in which the pump is operated by a separate electric motor.

MAIN FUNCTIONS OF Hyundai Getz Power Steering Oil

Hydraulic fluid performs important role in the operation of the entire Hyundai Getz power steering unit, its main function is to transfer energy from the power steering pump to the pistons of the steering mechanism and cool the entire unit. Also, thanks to the Hyundai Getz power steering fluid, the duration of the operation of all parts of the mechanism is greatly increased, it prevents the occurrence of corrosion and oxidative processes. In addition to these properties, the lubricant significantly reduces friction between the elements and prevents overheating of power steering parts. With an insufficient level and unsatisfactory quality of oil, a complete failure of the entire mechanism can occur.

POWER STEERING OIL TYPES

To top up or replace fluid, use the oil recommended by the manufacturer. Hyundai car getz. Japanese car manufacturers allow fluid to be poured into the power steering system for automatic transmission(ATF). European ones indicate the need to fill only with special oils (PSF). By outward signs they differ only in color, and we will talk about the main and additional characteristics later.

• degree of viscosity;
• mechanical characteristics;
• hydraulic properties;
• composition of chemicals (type of additives);
• temperature characteristics.

You can evaluate the properties of the oil by its color, which is also important parameter. Power steering fluid of the same color can be mixed with each other. It is not allowed to mix mineral and synthetic oil, even if it has the same color.

• red transmission oil can be used for both power steering and automatic transmissions (automatic transmissions), but is not suitable for all vehicles, it can be made both on a synthetic and mineral basis;
• yellow liquid universal used for power steering, automatic and mechanical transmissions;
• green oil is used for hydraulic boosters and mechanical transmissions, has a more viscous consistency, is made on the basis of synthetic and mineral ingredients.

In addition to the above characteristics, it is necessary to pay attention to the basis on which Hyundai Getz power steering fluid is made:

• the mineral base has a positive effect on seals, oil seals, gaskets, etc., as much as possible protects the rubber parts in the hydraulic booster from adverse effects, to the advantages mineral oils can be attributed to low cost. When choosing this type of oil, you need to be aware of its shortcomings: high viscosity, tendency to foam, and a short period of operation.
• synthetics - it contains fibrous rubber ingredients that have a detrimental effect on rubber seals and parts located in the Hyundai Getz power steering unit. Recently, due to the addition of silicone to synthetic fluids, harmful substances are neutralized, so the scope of synthetics is steadily increasing. Synthetic-based oil has a number of advantages: it has a long service life, works stably under any temperature conditions, has a low viscosity, and also has good operational characteristics, lubricating, anti-corrosion properties, not prone to foaming and rapid oxidation.

Whatever good oil however, when choosing it, first of all follow the recommendations of the car manufacturer, only the manufacturer, guided by the design of the pump and the entire Hyundai Getz power steering system vehicle can know 100% which specifications, chemistry, properties and base are best suited for your vehicle.

HOW OFTEN SHOULD YOU NEED TO CHANGE A Hyundai Getz Power Steering Fluid?

Power steering fluid replacement is an integral part of maintenance. Most car manufacturers recommend replacing Hyundai Getz power steering oil after 100 thousand km or after 2 years of operation. If you do not know when the fluid was last replaced, you can determine its production by such signs as: darkening, various impurities, the smell of a burnt substance. You can also do a little testing: you need to take a few drops of the contents from the power steering expansion tank and drip onto a white paper sheet or napkin. If the color of the oil is light, pronounced, the oil is still suitable for use. If there are visible mechanical particles on the surface of the wipe, the liquid is cloudy with a burnt odor, it should be replaced immediately.

It is necessary to carry out the fluid replacement procedure in case of repair work power steering mechanism or dismantling the Hyundai Getz steering rack. Even a relatively new oil after the repair work must be changed.

SIGNS INDICATING THE PRODUCTION OF GUR LIQUID

• partial leakage of lubricant from the Hyundai Getz hydraulic booster, as indicated by spots on the ground and vehicle elements;
• an increase in the effort applied when turning the steering wheel;
• the appearance of unusual sounds when turning the steering wheel;
• steering wheel jamming in extreme positions;

If you find one or more of the above signs, be sure to check the condition of the power steering fluid, if it is unsatisfactory, be sure to contact the service station to replace the fluid.

Regular maintenance helps extend the life of your Hyundai Getz car. One of the elements of the machine that needs timely maintenance is the power steering.

The power steering is not a separate element, but a system that reduces the load while turning the steering wheel, reduces various shocks and vibrations. Power steering is a comfortable control of the machine.

The main elements of the power steering are: pump, expansion tank, distributor, hoses, drive belt and hydraulic cylinder. Liquid is poured into the expansion tank, which also belongs to the main elements of the hydraulic system.

The reliability of the entire power steering system depends on the availability of high-quality fluid. Like any other lubricant, gur oil should be changed periodically. Replacing the Hyundai Getz power steering fluid is a procedure that must be carried out, taking into account the recommendations of the manufacturer's car operation or after examining the condition of the lubricant.

If there is a change in color, lack of transparency, a burning smell, the Hyundai Getz power steering fluid should be replaced immediately. This will help prevent loss of vehicle control and unscheduled repairs to the power steering system.

How to change the power steering fluid in a Hyundai Getz?

Maintenance of a Hyundai Getz car is carried out with mandatory observance of safety requirements.

Basic safety requirements:

• Carry out oil changes away from children and pets;
• Do not lift a load that exceeds the norm;
• Wipe up spilled liquid immediately;
• Use proper tools;
• Use gloves, wear overalls;
• Check the correct operation of the lifting equipment.

According to the recommendation written in the manufacturer's instructions, replacing the fluid in the power steering with a Hyundai Getz is a periodic procedure carried out every 50-60 thousand kilometers of the car. The lubricant should also be changed if there is a change in color, turbidity and the appearance of an extraneous odor.

An untimely oil change leads to noise in the power steering during movement. This is why there is a hum in the power steering system:

• Low level of lubrication in the power steering system. You should look for the cause of the leak in the pump or rail;
• The use of low-quality liquid in the gur, which will lead to a breakdown of the entire system;
• Poorly tensioned drive belt;
• Air entering the gur during the lubrication process. If air has entered the hydraulic booster, the fluid will begin to foam.

To avoid problems in the operation of the power steering system, it is necessary to constantly check the power steering fluid in the Hyundai Getz, the level in the expansion tank and replace it if necessary.

Pour power steering fluid into the hydraulic system in a Hyundai Getz with a PSF-3 approval, for example, RAVENOL PSF Fluid, with a volume of 2 liters - one liter to drain the old oil, and the second to fill in new fluid. Other types of oil will damage the power steering pump.

Can be used in Hyundai Getz ATF SHC, 1.3 - 1.5 liters. It is recommended to fill in liquid, for automatic box gears - ATF TOTAL FLUIDE XLD FE. Due to its composition and properties, this oil ensures reliable operation of the front steering wheels.

First step

To successfully carry out the replacement, it is necessary to prepare the tools for the oil change process. The list of Hyundai Getz power steering fluid replacement tools includes:

• Large syringe with a tube;
• Container for working out;
• Clean rag;
• Rubber or plain gloves;
• New oil.

When preparing the tools necessary for the job, you should determine how to install the car. The car can be installed on a viewing hole by hanging the front wheels. Thus, the load from the power steering will be removed. You can also raise the front of the car with jacks. The owner of the machine independently decides how to install it. Changing the oil in the power steering can be done in two ways - a partial replacement of the Hyundai Getz power steering fluid or complete replacement Getz power steering oils.

Second phase

At partial replacement lubricants, draining fluid from the Hyundai Getz is performed as follows:

• Raise the hood, unscrew the cap of the power steering reservoir;
• Pull out all the oil from the gur tank with a syringe with a tube.

Draining the oil in a partial change is now complete.

With a complete replacement of the fluid in the power steering, draining the old oil is carried out as follows:

• Raise the front of the machine;
• Using a syringe with a tube, pump out the lubricant from the expansion tank of the power steering;
• Disconnect the hose that comes from the radiator from the tank. Lower the end of the hose into the prepared container. Plug the hole in the expansion tank;
• With the power unit not running, turn the steering wheel all the way in both directions. Old liquid will begin to flow out of the system into the container;
• After draining the used grease, it is necessary to flush the power steering system. To do this, 200 ml of new oil is poured into the expansion tank of the system.

The flushing process itself is the same as the procedure for pushing fluid out of the system. Rotate the steering wheel to different positions until it stops until all the flooded flushing is out of the system. Repeat washing if necessary. After draining the old oil and flushing the power steering system, you can start filling in new grease.

Third stage

With partial replacement, fill in new fluid as follows:

• After pumping out the old fluid, fill in new grease with a syringe with a tube to the maximum level;
• Start the power unit and turn the steering wheel to the extreme position in different directions;
• Stop the engine and repeat everything until a light grease appears.

At full shift in the Hyundai Getz, the replacement of the power steering fluid is completed by the process of pouring new fluid into the hydraulic system. For this you need:

• Install the return hose in place;
• Fill in new oil up to the max mark;
• Gently turn the steering wheel all the way to the right and left, power unit do not start;
• At this point, the old power steering fluid will begin to flow out of the drain hose. Oil from the power steering reservoir will go throughout the system. Add power steering fluid to the Hyundai Getz expansion tank;
• Again turn the wheels in different directions. Repeat adding and swirling until a light-colored oil appears in the container. To purge the power steering pump of air, start the engine for a few seconds. Fluid should come out through the drain hose. Make sure that the oil does not completely drain out of the tank;
• Making sure there is no air in hydraulic system, put everything in place;
• Remove the remaining grease from the tank, remove the plug - hose and connect the return hose to the expansion tank;
• Add oil to the maximum level, start the engine by turning the steering wheel in different directions. If the level is low, add oil.

Remove the Hyundai Gutz car from the inspection hole or jack. After a few days, it is necessary to check the fluid level in the power steering system.