A car is not a luxury, but its maintenance is not the cheapest event. Every car owner wants his car to be special and begins to bring it to such a state. The very first desire is to tint the windows of the car.
This procedure is quite complicated, but quite real. You can drive your car to a specialized workshop, but you can do it yourself. Next, we will consider step by step how to tint the car yourself - with your own hands.
Before starting work, you need to collect everything that we need:
- tint film (the result and complexity of the work depends on the quality of the material);
- soft rubber spatula (very often plastic spatulas come with tinting, but they scratch the surface and can tear it);
- stationery knife with a set of blades (knives that come with tinting are uncomfortable and blunt);
- window cleaner, warm water, a rag (it is advisable to use a soft and lint-free rag);
- a spray bottle (can be used from window cleaner. The container should be filled with soapy water, tap water with the addition of liquid soap or dishwashing detergent is suitable for this);
- household hair dryer (this item is not mandatory, but it greatly facilitates and speeds up the work).
Now that everything is prepared, it is advisable to drive the car into the garage, you can also glue it on the street, but any gust of wind can ruin everything.
Next, you should prepare the windows for work. Correctly sticking tinting material is possible only on perfectly clean windows. It should be remembered that there should be no remnants of the old tinting and glue from it on the glass.
Having completed all the preparatory work, you can proceed to the main business, it is desirable that you have an assistant next to you, which will be needed when fitting the blanks.
Side window tinting
It is better to start tinting a car with your own hands from the side window, as it has a small area and is quite straight. We open the door, the glass should be raised to the very top. It is advisable to remove the side seals, as they will interfere with operation.
Next, a blank is cut out, which is tried on on the outside of the surface to be glued. At this stage, you need to be careful and remember that tinting consists of two layers - the main and protective. The main one remains on the window, and the protective one is removed.
Having dealt with the parties, the workpiece is applied to outside glass protective layer up. It is advisable to moisten the surface with soapy water to make it easier to straighten the workpiece. Then it is trimmed along the glass contour with a margin of 5-7 mm. Now the modified workpiece can be removed and the surface wiped dry.
In the next step, you may need an assistant, as the work must be done quickly. A soapy solution is applied to the inside of the glass, this must be done so that there are no dry areas left on it, but there is no need for drips either.
Now the film should be separated from the protective layer. This should be done gradually - with your own hands you separate the main and protective layers, and your assistant sprays the adhesive part from the spray gun. This procedure must be carried out quickly so that the glass does not have time to dry.
The next stage begins with applying the workpiece to the work surface and leveling it. Having applied the material, it must be leveled over the entire area of \u200b\u200bthe glass with a soft cloth. Remember that until the film is dry, it is very easy to damage it.
After the tinting is completely straightened, we begin to expel air bubbles and the remnants of the soap solution from under it. This is done carefully with a spatula. Until the film is completely glued, it must be held with a rag, and water and air should be expelled from the center to the edges with a spatula.
After completing this procedure, it is necessary to trim the excess with a clerical knife. Trimming is performed 3-4 mm from the edge of the window - such a gap will eliminate the possibility of scoring.
This completes the tinting of the side glass, you can proceed to the next one.
Of course, if you have a hair dryer, the drying process can be greatly accelerated. In this case, you need to be careful, as the material may begin to melt under the influence of high temperature and you have to start all over again.
Rear window tinting
Tinted rear glass with your own hands - quite difficult. The difficulty arises due to the fact that it has a curved shape and a large area. In order to do everything correctly, a number of requirements must be met. You should start with the right choice of material.
The standard canvas has dimensions from 50 to 200 cm wide and 300 cm long. It is advisable to tint the rear window with a single piece of film, but this is a rather complicated procedure and you need to use high quality material for it. Let's start with the hard way.
To make a blank from a single piece, you will need talcum powder, which can be purchased at any pharmacy, as well as a household hair dryer. The surface of the rear window is covered with talc and tinting is laid on it - with a protective layer up.
It is talc that has to be used, and not water, for the reason that it will not dry out under the influence of temperature. Further, with the help of a hair dryer, the film is given the necessary shape. This is done from the center. The whole procedure is a gradual preparation and its alignment with a spatula.
Working without an assistant is almost impossible. After the workpiece over the entire surface of the base takes its shape, trimming is performed, with a margin of 7-8 mm. And the procedure begins, completely identical to the tinting of the side windows.
If it is not possible to tint the rear window with a single piece of film, then you can do this with the help of three strips. This procedure is quite simple and begins with toning the upper part of the base. The whole procedure is carried out according to the standard scenario.
With this method, the window surface should be washed after applying each layer. The second layer is glued to the very bottom of the glass, as this is the most difficult area. Now the middle remains, which is tinted last. Before pasting it, it is recommended to dry the previous strips.
For pasting the last strip, a piece of film is taken, with a margin of 5-6 mm. This margin will be needed to eliminate the possibility of non-tinted areas.
At the end of the work, these overlaps can be left, as they will be visible only from the salon, or can be removed with a clerical knife. If everything is done correctly, then the overlap will completely close the junction.
Now we can say with confidence that do-it-yourself car tinting is over. The car can be used, but the windows with the applied film cannot be opened for 2-3 days.
Nowadays, tinting the rear window of a car is a common thing. Considering the fact that in the presence of rear-view mirrors there are no special requirements for the light transmission ability of the tinting of the rear hemisphere, its darkening can be of any degree to your liking. How to tint the rear window? For this, it is not necessary to contact a car service. A car service will take you both time and money, and not small ones. If you have the desire and a minimum of skills, you can do the tinting of the rear window yourself. Pay only for a roll of film and gain invaluable experience.
Glass tinting has a number of positive aspects. Tinted rear window protects from direct sunlight, reducing the heat inside the car on a hot summer day. Also, thanks to her, the interior upholstery is more protected from fading, and plastic ones were made from cracking. This is especially true for interiors with leather upholstery. The skin dries out and cracks when exposed to the sun.
Toning is also in a good way protection of personal space, hiding the interior of the car from prying eyes. An important factor is the fact that in the event of a traffic accident, tinting will protect the glass from the scattering of fragments. Thus, it allows you to reduce the degree of possible injuries. How to tint your car?
The choice of tinting
The most common and affordable way to tint the rear window is to use a tint film. By the way, if we talk about the most modern achievements in the field of tinting, then it is worth mentioning the so-called electronic tinting, which has recently appeared on the auto services market. Her main feature is unique property change its light transmission capacity in seconds. One press of a button on a special key fob, and tinted windows turn into ordinary ones. One more push and vice versa.
However, this tinting is still a luxury due to the high cost (up to 10 thousand US dollars). It is also impossible to perform it at home, as it requires special equipment. Conventional tint film is affordable and is manufactured in a wide range of color scheme. Therefore, if you are thinking about how to tint the rear window, I can safely recommend its use.
Video "Instructions for tinting the rear window"
Provided in this video detailed instructions with a description of the rear window tinting process.
DIY tinting
Each case requires appropriate preparation. We need to tint the rear window:
- roll of tint film;
- building hair dryer;
- rubber spatula (you can use a plastic spatula);
- a clean rag or rag that does not give a lint;
- spray;
- the most common hair shampoo;
- sharp knife (you can wallpaper with a retractable blade);
- glass cleaner.
As you can see, quite an affordable set of tools and fixtures.
Preparation
If possible, it is easier and more convenient to tint the rear window with the glass removed. In this case, you will get convenient access to the glass and be able to perform all the necessary operations in comfortable conditions. The first and, perhaps, the most important operation is washing and cleaning the glass from both sides from dust, dirt and grease.
The appearance of tinting will also depend on the quality of cleaning. The slightest speck of dust on the glass can lead to a white speck. For the same reason, glass cleaning cloths should be lint-free.
Film application
Before sticking the film, you will need to cut off a piece of the required size and shape from the roll. In this case, the piece should be with a margin around the edges. A couple of centimeters will suffice. With the glass removed, it is convenient to do this by applying the film to the glass lying on the table. It is applied from the outside of the surface and cut off with a knife or scissors. If the glass is installed on the car, then it will not be so convenient to do this, but it is also possible. You can also make a pattern using tracing paper or other suitable material.
If the glass is installed on the car, I can recommend removing protective layer already in the car. In this case, an assistant who will splash on the film will be useful. When smoothing, the edges of the film must be filled under the seals.
After the film dries, it will finally stick to the glass. As you can see, tinting the rear window is not difficult at all.
How to remove tint
If necessary, tinting is easy and simple to get rid of. To do this, it is enough to remove the film. It is not difficult to separate it from the glass. A layer of glue remains on the glass, which is washed off with a solvent such as white spirit, gasoline or another. The most suitable solvent for your type of adhesive can be selected empirically.
Video "Do-it-yourself rear window tinting"
This video shows the procedure for applying a tint film on the rear window with your own hands.
Each driver decides for himself whether to do the tinting of the car. You can go to a car service and pay a lot of money for services. And you can study in detail the presented article on how to properly tint the car with your own hands, and do everything yourself.
Why you need to tint your car
If you want to protect yourself from prying eyes, the best option will toned car. Tinting has a few more useful features.
- The film coating is distinguished by the property of reflecting heat rays. In summer, it will not be so hot inside the car, the plastic elements will not heat up, and the sun's rays will not annoy the driver and passengers.
- The film blocks ultraviolet light. In the cabin, the windows of which are covered with a tinted coating, the upholstery and plastic elements will not fade so quickly.
- Provides extra strength. Tinted windows are harder to break.
- Such tuning improves the appearance of the car. The design of the car acquires a certain gloss and chic, of course, provided that your vehicle is well-groomed and clean.
Types of tint films
A variety of film coatings catches a person who wants to tint windows on their own, literally by surprise. To do right choice, you need to decide which glass you plan to tint, and what features toning should perform.
Coatings designed for the windshield, front side window, rear side window and rear window will differ in their light transmission.
Also film coatings differ in color. The color pigment is part of the structure, but the more it is, the lower light transmission properties. You can also install metallic tinting. It has a high reflective ability, but at the same time creates certain interference with cellular communications. In addition to the above film coatings, reinforcing films are produced, they are often called "Armored".
Top film brands:
- LLumar (used by 70% of crafters)
- SunGuard
- Infinity
- contrast
- Johnson
- SolarGuard
- sun control
How to choose a tint so that you do not have to remove it
There are situations when toning required to be removed, it happens:
- when the light transmission capacity does not meet the requirements of traffic rules;
- when the material turned out to be of poor quality and defects began to appear;
- when the color of the coating spoils the appearance of the car.
Checkpoint degree directly affects driving safety vehicle. Exist technical regulations requirements, which specifies the allowable transmittance.
If these requirements are not violated, you can drive a car without fear of traffic police fines.
These rules state that light filter:
- For the front has a tolerance of at least 75%
- For lateral - not less than 70%
The rear is not standardized, it can be installed there opaque tinting or transparent with minimal light transmission, with the exception of a mirror film coating.
Now that you have decided on the parameters of light transmission, we advise you to pay attention for quality film tinting coating. The most durable and best quality is metallized film but it also costs more. But the dyed material is cheaper, it will last less, only 2-3 years.
If you have no pasting experience do it yourself, it is better to opt for an inexpensive dyed film. However, the cheapest tint in the store is also not worth buying. In such products, the front material itself and the glue are far from the best quality.
We prepare materials and tools for tinting with our own hands
The best place to do this kind of work is well lit garage.
On the street you can not tint: wind, dust, midges will make a negative contribution.
What to cook:
- buy the required amount of film, it is better that it be a little more, taking into account the fit;
- spray;
- soap or liquid detergent;
- pure water;
- blade, construction knife or for cutting paper;
- cloth napkins;
- a plastic spatula for smoothing the film and removing air bubbles from under it (often distillation is included with the film);
- high power hair dryer.
Also prepare a glass scraper. Make a soap solution, for this, dilute a couple of drops of detergent in 500 ml of water.
Tinted car side windows
Before pasting the side windows take the glass out and wash with soapy water.
We make a pattern of tint film
Before tinting, make a pattern from the film. For cutting, you will need a table, it must be clean and suitable in size in order to cut the material not only on the side windows, but also on the rear window.
Cutting must be done taking into account allowances for errors, we apply the film to the glass and add 5-7 mm from all sides, with help marker, mark the cut line and cut it out. If the glass won't stretch, edge make the minimum, 2 mm.
Side window tinting sequence
There is a blank, now we proceed to gluing.
- The entire area to be pasted before to fix tinting, moisten abundantly with soapy water from a spray bottle.
- The gluing process starts from the top. The protective layer is removed from the film by two-thirds and also sprayed with a solution. You also need hands moisten water.
- The workpiece is applied adhesive layer and aligned to the top edge.
- If everything is smooth and there are no gaps, proceed to distill the liquid from the center to the edge. These actions must be carried out carefully. The film can then slide over the surface. Use a soft cloth, then a hard spatula and a hair dryer.
- After removing the bubbles, the protruding edges of the pattern are cut off with a clerical knife.
- Next you need paste and also smooth out lower part. The protective layer is removed from the pattern, the adhesive layer is moistened with soapy water and applied to the glass surface. The distillation of the liquid is carried out in the same way as when pasting the upper region. To not be vertical folds, follow the direction movements: from the center to the edges.
How to tint the rear window of a car
When toning rear window It should be borne in mind that heating threads are located on it. heating elements it is necessary to carefully clean from dust and specks and wash the glass.
We make a pattern of a film for tinting the rear window
Rear glass for tinting do not take off, so the pattern is made right there “in place”. The sheet is applied to a wet glass surface (for this it is necessary to spray the glass abundantly with a solution) and cut out with a good margin, 2-3 cm. Then the workpiece is applied again and the excess is already cut off.
Stages of rear window tinting
The technology of gluing the film on the rear window does not differ from the process of tinting the side windows.
- Spraying the glass surface with soapy water.
- We apply the pattern, remove the protective layer from it by two thirds, spray the adhesive layer too.
- Using the method of smoothing from the center to the edges, we remove air bubbles and all liquid from under the material, correct the creases and align the folds. We make sure that the pattern does not move during the knurling process.
Errors in work happen even among experienced craftsmen, the main thing is to eliminate them in time. Therefore, sticking is best done with a partner.
If result does not suit, for example, there are bubbles left, they must be “expelled” from under the material with a spatula. This is easy to fix when the tint is still damp. If the film has already “grabbed” well with the glass surface, and the vertical creases, it can be heated with a hair dryer or steam generator.
Sometimes, especially for beginners, the pattern starts to move out, the curvature can be removed by heating the material with a hair dryer, peeling it off and repeating the whole operation again.
The film coating dries completely in about a day. At this time, it is better not to go anywhere, and if the trip cannot be canceled, it is recommended not to open the windows and it is advisable not to turn on the air conditioner.
Learn more about the process car tinting You can from the next video.
Author
For 15 years I have been repairing various types of cars, including brands such as VAZ, UAZ, Chevrolet, Mazda, Kia and many others. Everything related to the box, engine or chassis. You can write me your question below in the comments and I will try to answer it in detail.
Many car owners try to change the look of their car the way they like. An important addition in this case is tinting. However, not everyone thinks that they need to tint their car - this is a personal matter for everyone.
The process of toning requires accuracy. Before applying the film, you need to prepare the surface. With experience in carrying out such work, you can perform glass tinting on your own without contacting specialists.
This article will discuss in more detail the process of gluing a film on glass, as well as its choice.
Choice
There are many types of tinting films on the market today. It is quite difficult to choose the right one among them, because you can talk about the pros and cons of each film for a very long time. It should be borne in mind that in no case should you take the cheapest tint made in China. Outside, it almost does not darken the glass, and from the inside, the view deteriorates significantly, which can lead to an accident. In addition, the Chinese film is difficult to glue, as it does not take the form of glass.
In order to choose a quality film, it is best to contact the sellers of the store. They will give you all the information you need and help you choose the right tools.
Necessary materials and tools
Glass tinting is a rather complicated process, which will require special tools, namely:
- Spray;
- Raquel;
- Napkins;
- Sponge;
- Scraper;
- Ruler;
- Special knife;
- Hairdryer, preferably building.
It will seem strange to many that the fact why a sprayer is needed when tinting. In fact, everything is simple. In order for the film to better adhere to the glass, a soapy solution is applied to both surfaces before starting the process. When preparing it, it is necessary to observe the proportions: 5 drops of detergent per 1.5 liters of water. For best result the solution must be shaken.
In order for the film to lay perfectly in the future, it is necessary to completely clean the glass. If they are too dirty, then the top layer is best removed with plain water, and then with a soapy solution.
Film pattern for side windows
In order for the film to stick perfectly and be easier to work with, you need to cut it to size. Before you start, you need to understand which side of the film has a sticky layer. It must be protected by a transparent material. It is best to cut the film in such a way that it touches the glass with the inside of the inversion. When cutting, it should be borne in mind that the film should protrude beyond the border of the glass by 0.5-1 cm, since the extra piece can then be cut off, and if it is not enough, it will be worse.
For precise cutting, it is necessary to apply a soapy solution to the outside of the glass. Next, you need to put a film there so that the transparent material is on the outside. The film must be placed so that it covers the entire surface of the glass. From below, it should slightly cover the seal. Next, you need to cut the tint film along the contour of the side seal, leaving about 1 cm in reserve, which must be threaded under the seal. Now you need to cut off the remnants of the upper part of the film, then pass it under the upper seal. The film should follow the contour of the glass.
If side windows deaf and do not fall, then you need to cut the film along the contour, leaving only a couple of millimeters in stock. In this case, you need to cut it out very carefully, as you can ruin the seal. To protect the elements of the car from scratches, it is best to apply a squeegee.
The remains of the film should not be left on the glass, but it is better to throw it away immediately, as they will interfere with further work. If blind windows are limited by a body without a seal, then the film must be cut out very carefully. The knife for this must be sharpened, if it becomes dull, it can damage the film and scratch the body.
Rear window pattern
The glass must be completely dry before application. Next, with a damp cloth or sponge, you need to apply 2 vertical lines closer to the edges and 1 horizontal line in the center. Now you need to put a tint film on the glass with a transparent material outward. When cutting, you need to leave a margin of a couple of millimeters.
Now we need to remove the leftovers. It is most convenient to do this with two people, so you need an assistant. He should smooth the film so that all horizontal creases disappear. To do this, you can use a squeegee. Vertical creases are best removed with a hairdryer, but this must be done very carefully, as there is a risk of overheating or burning the film. After that, you need to smooth the film with a squeegee so that it takes the form of glass. This must be done from the center to the edges, in all directions. Actions must be careful so that creases and folds do not appear again, since it will be almost impossible to remove them later.
Now you need to use a flashlight or other device to check whether the film has been removed everywhere. To do this, the lamp must be placed in the cabin near the glass and all residues that go behind the seal must be removed from the outside, leaving literally 1-2 mm in reserve.
Applying film to side windows
Now the main part is the application of the film. You need to start by wetting the glass surface. Next, you need to clean the entire surface with a scraper. After that, it is necessary to wipe the glass with a cloth, and then dry it completely.
Next, you need to apply a soap solution to the surface of the glass from the inside. After that, you need to remove the transparent material from the film. So that it does not stick together, you also need to wet it with plenty of soapy water. It is most convenient to remove a little the transparent part and immediately apply the solution. It is also advisable to wet your hands so that they do not stick to the film.
Now you need to apply the film on the glass, it should lie exactly along the contour, without touching the seals. Next, you need to level the top of the film and glass. After that, you can start leveling. You also need to remove all bubbles and bumps with a squeegee. You need to do this from the center to the edges. When the film has stuck perfectly, it is necessary to remove the remaining film with a knife. After the process is completed, it is not recommended to touch the film until it dries.
Rear window application
Cleaning the rear window does not allow the use of a scraper, as it may damage the heating lines. It must be done only with a sponge. Then it is necessary to dry the glass completely.
Next, you need to wet the glass abundantly. Before doing this, you need to cover the rear shelf with a dry cloth or other material. Now you need to remove the transparent part from the film and moisten it with plenty of soapy water. You will need an assistant to apply the film to the glass. Together with it, you need to stick the film and align it on the top. Next, you need to remove all bubbles with a squeegee. This can only be done horizontally so as not to damage the heating threads. After the process is completed, the film should not be touched for about 2 days.
Outcome
Car window tinting is a tricky business. From the first time, almost no one succeeds in sticking the film neatly. Therefore, if there is no experience in applying tinting on car windows, then it is better to contact the masters. The cost of such work is different.
Video
How to tint a car? This is a question that deserves special attention. Appearance a vehicle with good design and amazing tuning - that's what attracts the eyes of everyone around. Toning refers to the elements of tuning. It is worth considering in more detail the question of how to tint a car, because thanks to tinting, the car will acquire charm, shine and presentability.
The tint film, among other things, prevents many unpleasant effects on the car. Among them, burnout of the skin, instrument panel, acoustics and audio equipment. In addition, tinting will create a barrier that will prevent the sun from blinding the driver.
When tinted with a film, car windows are not dismantled. Maybe only the door panels are removed - and then very rarely. In addition, this is a very fast process: a car can be fully tinted in three hours. This does not scratch the glass. Another plus that a tint film for cars has is that it can be removed at any time, and the windows will remain intact. It is also heat-resistant: it is not afraid of overheating or frost. It does not reflect, does not demetallize, does not flake or bubble. Plus she don't miss
How to tint a car with your own hands? Not as difficult as it might seem. To do this, you will need an eraser spatula, shampoo, a knife, a blade, a ruler and a film.
How to properly tint a car? First you need to wash it thoroughly, washing off all the fat from the glasses. If you do not do it efficiently, then hairs, dust particles will clog under the film, and this is fraught with a bad result. Then you need to measure the glass (an allowance of five centimeters on each side is taken into account), and you can proceed to the film, or rather, to cut it. You need to find the transparent side of the film. Then you should take the film and sprinkle it with plenty of water, in which there is a sufficient amount of shampoo. The film must be damp, and even wet. Then it is divided to the end (it is necessary to ensure that its sides do not stick together), and the transparent part is thrown away. The adhesive side of the film is applied to the car glass. Then you need a rubber eraser, which from the center will need to drive water to the edges. The film must be held so that it does not slip off. Attention! You need to remove ALL the water. Then, after an hour, you can cut the film. But by no means exactly along the edge - for this you need to wait about 8 hours. You can dry the film with a hair dryer to improve the result.
How to tint a car, or rather, its rear window? The film is attached to it in a different way. You need to first carefully examine it, then wash it thoroughly. Fastening starts from the top. The washing liquid should be spread over the top of the already washed glass. Then 1/3 of the film is separated and the liquid is abundantly sprayed onto its surface. The same operation will need to be repeated with the remaining 2/3 of the film. As already mentioned, it will be necessary to wait a few hours, after which it will be possible to correct. And finally, the last 2-3 days you do not need to open the windows to avoid possible deformation (this is if the film is not of the highest quality).