Portal for car enthusiasts

Adding oil to the getz engine 1.1. Recommendations for changing the oil in a Hyundai Getz engine

Fill the system with oils that comply with the VW 500 00, VW 501 01 and VW 502 00 standards.

PROCEDURE
1.
2. Start the engine and warm it up to operating temperature. Stop the engine and wait a few minutes for the oil to drain into the oil pan.
3. Remove plug 1 (see fig. ) or 6 (see fig. ) of the oil filler neck.
4.
5. Unscrew plug 15 (see fig. Parts of the engine lubrication system 1.0 l, 37 kW and 1.4 l, 50 kW) or 29 (see fig. Details of the engine lubrication system 1.4 l, 55 and 74 kW) drain hole on the engine crankcase, after substituting a container under it, and drain the used oil.
6. Screw in the plug, replacing the O-ring 16 with a new one (see fig. Parts of the engine lubrication system 1.0 l, 37 kW and 1.4 l, 50 kW) or 28 (see fig. Details of the engine lubrication system 1.4 l, 55 and 74 kW).
7. Unscrew the oil filter 4 with a special wrench (see fig. Parts of the engine lubrication system 1.0 l, 37 kW and 1.4 l, 50 kW) or 12 (see fig. Details of the engine lubrication system 1.4 l, 55 and 74 kW).
8. Lubricate the O-ring of the new filter with engine oil.
9. Screw on the new filter by hand without using a tool.
10. Pour in the required amount new oil, controlling its level by the pointer.
11. Start the engine and let it run for a few minutes Idling. Stop the engine, check the oil level and top up if necessary.

Tightening torques for the oil drain plug, Nm

DIESEL ENGINES

The filling volume of the lubrication system with an oil filter is 4.5 liters.

Fill the system with oils that meet the standards:

- engine 1.9 l, 74, kW - VW 505 0;
- engine 1.9 l, 47, kW - VW 506 00.

PROCEDURE
1. Park the vehicle on a level, level ground.
2. Start the engine and warm it up to operating temperature. Stop the engine and wait a few minutes for the oil to drain into the oil pan.
3. Remove the oil filler cap.
4. Remove the engine splash guard.
5. Unscrew plug 18 (see fig. Parts of the lubrication system diesel engine ) drain hole on the engine crankcase, after substituting a container under it, and drain the used oil. Screw in a new plug.
6. Unscrew cover 1.
7. Take out the filter element 4.
8. Install a new filter element, replacing the O-ring 3.
9. Screw in a new cap 1 with a new O-ring 2. Cap tightening torque oil filter- 25 Nm.
10. Fill in the required amount of new oil, controlling its level on the pointer.
11. Start the engine and let it idle for a few minutes. Stop the engine, check the oil level and top up if necessary.

Changing engine oil is one of the most frequent procedures that is carried out during Maintenance. Not using the services professional service You can change the oil yourself. The more often this procedure is carried out, the longer the engine will last. internal combustion and car.

When is an oil change required?

The Hyundai Getz oil change schedule recommended by the manufacturer is once every 15 thousand kilometers. But the actual operating conditions, especially in Russia, are very different from the conditions under which the vehicle manufacturer tested. Therefore, the replacement of motor oil should be carried out approximately once every 8-10 thousand kilometers. It is recommended to check the oil composition periodically. If metal chips are present in its consistency or the liquid has darkened, it will have to be replaced more often.

Signs of a need for replacement:

  • Extraneous noise in the power unit;
  • Deteriorated vehicle dynamics;
  • Reduced fuel consumption.

What kind of oil to fill?

Engine oil selection Hyundai Getz- original. The manufacturer recommends that only original oil be used in the engine. But there are analogues that, in terms of the quality of the composition, are in no way inferior and, on the contrary, even superior.

Suitable for Hyundai Getz synthetic oil with viscosity 0W30. A similar fluid is designed for the Hyundai engine of all models. Car oil has excellent lubricating properties. These parameters favorably affect the internal elements power unit. The liquid contains special additives that, during the operation of the power unit, destroy mud deposits and eliminate metal chips. An oily liquid with such parameters is an ideal choice for Russian climatic conditions. With such a liquid, the engine can be started even at a temperature of -30 degrees Celsius. The oil is selected according to the SAE class.

Well-known oil producers:

  • Mobile;
  • Lukoil;
  • Rosneft;
  • console;
  • Valvoline.

Stages of changing the oil in a Hyundai Getz engine

Before starting the oil change procedure, preparation for work is carried out. To do this, you need to find a place with a lift, a viewing hole or a flyover. After prepare essential tool and materials.

Necessary tools and materials:

  • A set of keys (hex, socket, wrenches);
  • Screwdriver;
  • Pliers;
  • Rags;
  • Container for waste fluid;
  • Oil filter;
  • Oil filter puller;
  • fresh oil;
  • Special clothing and gloves

How to drain oil?

The sequence of actions for draining oil from a Hyundai Getz engine:

  1. Before draining the oil, the liquid must be warmed up.
  2. Turn off the engine on the overpass, inspection hole or lift.
  3. Unscrew the crankcase protection with a 10 mm wrench. In addition to the drain plug, it is necessary to pour oil into the motor to drain the lubricant.
  4. Substitute a container for waste fluid. Oil will start to flow from the pan. In parallel with this event, replace the oil filter. To do this, a new filter must be prepared. Pour about 100 grams of oil into it and lubricate the sealing rubber ring.
  5. spin drain plug.

How to clean the engine?

Step by step instructions for cleaning the engine:

  1. To clean the power unit from carbon deposits, a flushing mixture is required.
  2. Pour the flushing mixture into the filler neck. Please note: the procedure is carried out if necessary, only with the old filter.
  3. Start the engine. Let it work for 5-10 minutes. Drain the fluid from the system by unscrewing the drain plug. The internal channels of the engine are cleaned.

How to fill in new oil?

Procedure for filling in new oil:

  1. After flushing the engine, a new one is poured oily liquid. The oil filter is pre-installed as described above. Oil is filled through the oil filler neck, which is located on the top of the engine.
  2. Filled with about 3 liters. The residual amount is poured in 100 grams, the dipstick is periodically pulled out to check the level. This is necessary in order not to overflow the liquid. If overflow occurs, drain excess oil.
  3. Bring the level to a mark close to the maximum (on the dipstick).
  4. Start the engine. Make sure the oil pressure indicator goes off. If this does not happen, turn off the power unit. Check all locations for leaks. Specifically the oil filter and drain plug. If smudges are visible, tighten harder. If not, restart the engine. The lubricant pressure indicator should go out.
  5. Let the engine run for 5-10 minutes. Silence it.
  6. Recheck the oil level. Top up if necessary.

The process of changing the oil in the Hyundai Getz engine with your own hands is completed.

Replacement frequency

The main factors affecting the frequency of oil changes:

  • Surrounding climatic conditions;
  • Place of operation of the vehicle (urban / suburban conditions);
  • Intensity of exploitation;
  • duration of oil use. It is recommended to change it at least once a year;
  • Mileage. Once every 8-15 thousand kilometers. Depending on operating conditions.

Despite the replacement regulations, you need to check the oil level much more often. This procedure will help to avoid oil starvation, which leads to costly overhaul Or even to replace the engine.

Each vehicle in the course of its operation needs an engine for a long and normal life. Timely completion of the shift engine oil helps prevent many problems. Firstly, it prevents the appearance of carbon deposits inside the engine and the oxidation of internal parts. Secondly, which is in a normal state, it helps the engine of your car to start easily in any frost.

To change engine oil in Hyundai Getz, about 3 liters of fluid are required.

Oil change interval

In addition to the fact that you must change the engine lubricant, you must also do it on time. In order to understand how often you need a Hyundai Getz engine, just look at the maintenance schedule for your car.

So, if we analyze the regulations for the technical Hyundai service Getz, we will see that the manufacturer recommends changing the engine oil for the first time after buying a car after driving 3000 kilometers. Each subsequent replacement should be carried out approximately once every 15,000 kilometers, subject to normal operation of the car. This is in the event that during this run you did not particularly subject your car to various kinds of loads. If you use the car not quite in a gentle driving mode, or just drive on bad roads and in mountainous areas, then the replacement frequency will decrease significantly. In this case, you should be between 11,000 and 12,000 kilometers.

Refueling volume of Hyundai Getz engines

The point is that in Hyundai cars Getz manufacturer installed a number of engines, these are 1.1; 1.3; 1.5 and 1.6. Due to the different displacement, each engine has its own filling volume. In the smallest engine of the 1.1 line, the filling volume is about 3 liters of oil. In the remaining motors of the line, namely 1.3 and 1.5 and 1.6, approximately 3.3 liters of lubricant are placed.

In addition, you must constantly audit and monitor the level of oil poured into the power unit. In order to check the level of lubrication on a warm engine, you need to get the dipstick under the hood of the car, which is usually yellow, wipe its lower part with a rag and put it back. Immediately after that, take it out and at the bottom you will see the level.

Choosing the Right Lubricant

In the instructions for operating Hyundai Getz manufacturer recommends using the original factory /KIA type viscosity 10W-40 or for regions with very cold winters, 5W-40.

If suddenly you cannot find an original lubricant of this type of viscosity, then you can choose a synthetic analogue for your car, but with a viscosity grade recommended by the manufacturer.

How to change engine oil in Hyundai Getz do it yourself

To begin with, with a key of 10, you need to remove the crankcase protection and unscrew, in addition to the drain plug, also the oil fill cap into the motor for easy draining of the lubricant.

After the mining from the pallet begins to pour out, we change the oil filter. As soon as we have drained all the waste from the pan and changed the filter, we can fill in new grease.

Do not forget that the amount of lubricant to fill in the engine is indicated in the operating instructions for your car, and you should not violate it. After a complete relubrication procedure, leave the machine engine running at idling for 15 - 20 minutes.

As you can see, the procedure is not particularly difficult, and we can carry it out in our garage using elementary keys, which are available in almost every car.

Oil volume in Hyundai engine Getz should be monitored regularly. To some extent, this can be attributed to one of the elementary procedures for servicing a car on its own. In addition, this includes the process of changing the oil, and the choice of the consumable itself. In the latter case, the driver is required to have a minimum set of theoretical knowledge. For example, you need to know compatible viscosity and tolerance parameters, oil change intervals, top brands, and finally, how much oil should be poured into the engine of a popular car.

Replacement frequency

Engine oil in the case of Hyundai Getz, according to official figures, is replaced every 15 thousand kilometers. This regulation may be adjusted downwards due to negative phenomena. So, let's highlight the main ones:

  • Operation at high speeds
  • Failure to comply with the speed limit of traffic rules, abrupt maneuvers
  • Driving on bad, dusty roads, in off-road conditions (muddy soil, mud, sand, etc.)
  • Operation in regions with frequent temperature changes (variable climate)
  • Operation in other conditions for which Hyundai Getz is not suitable.

Any of the above factors can cause the oil to quickly lose its beneficial properties. In this regard, a more frequent oil change will be required - for example, after 7 thousand kilometers. In such conditions, the regularity “the more often you change the oil, the better it will be for the reliability of the motor” is relevant. However, this applies to any transport. To prevent rapid wear of engine components, it is important to regularly check the volume and condition of the oil.

Volume and condition check

An oil dipstick is required to check the volume of the consumable. It is located in the oil filler neck. It has Min and Max marks. If the oil print is between them, then this can be considered the optimal level. Any deviation from the norm (for example, underfilling or overfilling) adversely affects the efficiency and reliability of the power unit. So, if the level is insufficient, add a little liquid. But this may not be enough if the situation is complicated by the following signs - the oil has acquired a dark brown color, contains mud deposits, and emits a specific burning smell. In such a situation, it is urgent to clean the engine of old oil, and only then pour in new fluid.

How much to fill

On the Russian market Hyundai Getz is well known with 1.4 and 1.6 liter petrol engines. They require almost the same volume of oil, equal to 3.3 liters. The full volume can be poured in after a major cleaning of the engine from the old fluid. Partial replacement, carried out at home, such a procedure, alas, does not provide. And yet, you can completely clean the engine with your own hands - for this you will have to change the oil several times every 600 kilometers. Continue until a clear liquid begins to flow out of the engine instead of the old black oil - this will mean that the cleaning is completed, and you can enter new oil in full.

The exact volumes of engine oil for Hyundai Getz engines separately for each year of manufacture:

Year of issue - 2002 - 2009
1.1l MPI 62 l. from. – 3 liters

Year of issue - 2002 - 2005
1.3l MPI 82 l. from. - 3.3 liters

Year of issue - 2005 - 2009
1.4l G4EE 97 l. from. – 3.3 liters

Year of issue - 2002 - 2005
1.6 MPI 105 HP from. - 3.3 liters.

Choosing oil for Hyundai Getz

The manufacturer recommends filling only the original lubricant manufactured by the Hyundai-Kia concern. It has viscosity ratings of 5W-30 as well as ACEA A3 tolerances. The oil has been assigned a proprietary specification 05100-00441, by which you can distinguish the original from the fake.

When choosing an analogue oil, one should be guided by the above parameters. So, you can pick up the perfect product, regardless of the brand. By the way, among the most famous companies with a recognized reputation, we will name Lukoil, Rosneft, Mobile, Castrol, Kixx, Elf, Shell and others.

Every car needs maintenance. It becomes no exception Hyundai Accent. It is necessary to change engine oil in the engine, according to the regulations, every 12-15 thousand km. Of course, you can contact a car service, but you can carry out a shift and with my own hands in half an hour.

Video

The video will tell you how to properly change the oil on a car, and also talk about some of the nuances of the procedure

Replacement process

Replacement Hyundai oils Accent is carried out quite simply with your own hands. For the process to be successful, it is necessary to have a minimum toolkit, as well as access to vehicle from below.

When everything you need is collected, you can proceed directly to the process itself:

  1. First, you need to let the car cool down.

    We are filming top cover engine. We unscrew the fastenings of the lower protection. We unscrew the engine protection bolts.

  2. We open the hood.
  3. Open the access cover to the drain neck.

    Find the oil filter plug.

  4. Unscrewing it will pour engine oil.

    We unscrew the drain plug of the engine oil.

  5. When the oil is drained, tighten the drain plug. To avoid smudges, it is necessary to replace the sealing ring.

    Drain the engine oil.

  6. Before filling the oil, we replace the oil filter element.

    Find the oil filter housing. Unscrew the oil filter housing.

  7. Go to engine compartment. To fill in engine oil, unscrew the filler plug.

After filling in engine oil, after 5-10 km of run, you need to look at the level. Add fluid if necessary.

Oil selection

  • SAE 5W-20, 5W-30;
  • SAE 10W-30;
  • SAE 15W-40;
  • SAE 20W-50.

Perhaps the most popular viscosity for Goetz is 5W40 and 10W40. Here is an example of popular brands and viscosities for our machine.

  • Aral High Tronic G SAE 5W-30
  • Mobil 1FS 0W-30
  • Castrol EDGE 5W-30
  • Motul Expert 5W-30
  • Mobil 1 ESP Formula 5W-30
  • ZIC Top 5W-30
  • Liqui Moly 5W-30 Top Tec
  • Shell Helix Ultra 5W-30
  • Castrol EDGE 0W-30
  • Elf Evolution 0W-30
  • Ravenol SSO 0W-30.

Remember that different viscosity grades must not be mixed and added to each other. Before changing the oil, you must completely drain the old one and use the flushing fluid!

Filter selection

Each filter should be replaced along with the engine oil change. They should be considered as one mechanism and they should also be serviced together. Recommendation for replacement every 10-15 thousand km or once a year.

Maintenance kit.

Diesel 1.5 engine (D4FA):

  • JP GROUP 3518500409
  • WIX WL7442
  • HENGST E208H D224
  • KNECHT/MAHLE OX 424D
  • BOSCH F 026 407 062

Petrol 1.1 l (G4HD, G4HG) (Cost from $3 to $6):

  • NIPPARTS J1310500
  • BLUE PRINT ADM52107
  • PURFLUX LS225
  • KNECHT/MAHLE OC 521
  • MEAT & DORIA 15131

Petrol 1.4 (G4EE):

  • PROFIT 1540-0740
  • BLUE PRINT ADS72101
  • ASHIKA 10-05-599
  • MFILTER TF 24
  • DENCKERMANN A210100

Output

Changing the filter and oil on a Hyundai Getz is quite simple on your own. To do this, you need minimal tools, as well as minor design skills. As for the choice of filter, it should be taken seriously, because how long it will last will depend on it.