Do-it-yourself generator for a Mishin healing coil. Tips for treating with a mishin coil

The optimal ratio of internal diameter to external diameter is 1/3
- Large flat coil - internal D - 70-80 mm, external - 240 mm, SHTLP-4 wire two cores.
- Flat coil 120-130 mm. internal D - 40mm, external - 120 mm, wire 0.5mm varnish. Optimal operating frequencies are 270-330 kHz.

How to make a Mishin coil with your own hands

Scheme for manufacturing a flat coil. D - 120-130 mm.

1. We start making a flat Mishin coil from the base. We make a base onto which we glue double-sided tape.
2. In the center of the base we install a round protrusion with a diameter of approximately 40 mm.
3. Take a varnished wire 0.5 mm in diameter and 10-12 meters long.
4. Around the round protrusion you need to wind two wires at once parallel to the plane of the base.
5. After manufacturing the coil, it is necessary to determine the frequency of operation of this container:

We make two taps from the coil. We take the end of one wire from the inside of the coil and the second from the other wire from the outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

Option 2

The flat coil works on minor problems such as viruses and fungal diseases. It can quickly remove scar tissue and speed up healing.

Manufacturing diagram of a large flat coil 250 mm

Option 1 (using a standard generator with a power of up to two watts)

We connect the oscilloscope probe in parallel to the generator terminals.

We gradually increase the frequency of the generator and look for the first frequency at which the output voltage of the generator is the lowest. This will be the operating frequency of this capacitance.

Option 2

We connect a resistor with a voltage of 1 Ohm in series in the power circuit.

We are looking for the first largest amplitude value.

Option 3 (if you don’t have an oscilloscope)

We make a flat inductor, the load of which includes 2 counter LEDs.

We look for the frequency based on the maximum luminosity of the LEDs.

For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.

A large flat coil allows you to work effectively at the level of the central nervous system, eliminating circulatory problems and many other small vortex problems of living organisms.

Scheme for manufacturing a toroidal coil (torus)

We make two taps from the coil: we take the end of one wire from inside the coil and the second from another wire outside. In this case, the circuit remains open, and the two unused outputs of the plates are simply cut off.

Option 1 (using a standard generator with a power of up to two watts)

We connect the oscilloscope probe in parallel to the generator terminals.

Option 2

We connect a resistor with a voltage of 1 Ohm in series in the power circuit.

We are looking for the first largest amplitude value.

Option 3 (if you don’t have an oscilloscope)

We make a flat inductor, the load of which includes 2 counter LEDs.

We look for the frequency based on the maximum luminosity of the LEDs.

For the above capacitance design, the approximate frequency is 280-320 kHz. In this case, the effective power range lies within ±10 kHz relative to the operating frequency.

The toroidal coil copes well with crystalline slags such as stones and sand. Thor also eliminates pain symptoms and works well with wound healing.

For more than a century, humanity has been widely using electricity. Countless devices of all kinds have been produced. At the same time, no one thinks about their safety.

Over the past decades, the number of pathologies of the human body, the treatment of which cannot be treated by medicine, has increased. The reason is often not so much a poor environmental situation as a lack of understanding of the processes in all devices that operate on the basis of the phenomenon of electromagnetism.

If we touch upon physical processes, then in nature they proceed in accordance with In simple terms, performing an action is impossible without a fulcrum, and during its execution, the object and the support receive equal mechanical influence. If you look at this problem through the prism of vortex processes, it turns out that when creating electromagnetic radiation, the electrostatic plane is taken as a basis.

The Mishin healing coil, reviews of which indicate that it has a high degree of functionality, provides vortex processes. They have a healing effect.

What does electricity radiation destroy?

Our life is full of continuous pulsations emanating from electrical devices. They have a destructive effect at the molecular level. As a result, increased energy saturation of molecules is caused, which leads to the formation of large clusters. Many looped structures of molecules in the human body cannot be treated with medications due to their high level of strength. Such formations in the body lead to the appearance of cancer or block any functions in the body.

The most unified method is to create a zone with a reduced density of the medium using electrostatic implosive resonance. This effect is provided by the Mishin healing coil.

The essence of her work is actually built on gravity. True, the range of the device is small. It is only 2-3 meters. The level of transmitted power of such equipment depends on the degree of voltage. The amplifier for the Mishin coil has an output voltage frequency of 12-24 volts. The current indicator should not exceed 100-200mA.

Principles of Flat Coil Manufacturing (DMA)

How to make such a device as a Mishin coil with your own hands? A preliminary preparation of a base is required, on which double-sided tape should be glued. A round protrusion is installed in the center. Its diameter is 25 mm. Around it, the laying of two wires begins, which should lie parallel to the plane of the base.

The generator for the Mishin treatment coil can be of a standard configuration. Its power is quite enough for health purposes. The generator circuit for the Mishin coil is presented below.

After manufacturing such a device, a container is obtained based on a pair of spiral-shaped plates that are nested inside each other. It is possible to use any copper wire, the diameter of which, together with the insulation, will be no more than 1.5 mm. The diameter of the coil should not be more than 23-25 cm. The wire is fixed at the top. You can secure it with tape.

The Mishin coil, the circuit of which is not so complicated, can easily be assembled independently. The materials for its manufacture are easy to obtain at any electrical appliance store.

How to set up a coil using an oscilloscope?

Mishin's vortex coil needs to determine the frequency. For this purpose, a pair of taps is made from the device. You should take the end of one wire from the inside of the coil, and the other end from the outside. In this case, the circuit remains open, and the two terminals of the unused plates should be cut off.

When using a standard type generator with a power of 2 W, it is possible to determine the operating frequency of the device by connecting an oscilloscope probe in parallel with the generator terminals. while gradually increasing. The first frequency at which the generator output voltage is lower is determined. This will be an indicator of the operating frequency of this device.

Second voltage measurement option

The device can also be measured using a 10 m resistor, which is connected in series. The highest amplitude value should be determined. This method makes it possible to evaluate the quality level of the supplied sine wave in load mode in the tank.

How to configure using the LED indicator?

The operating frequency of the capacitance can be determined using an indicator coil. It is an induction device that includes two counter LEDs.

With this method, you can find the frequency by the maximum luminosity of the LEDs. In this case, the generator voltage decreases. This ensures a reduction in the frequency range at which the glow is observed.

Effective coil frequency indicator

If you ensure that the wire is firmly fastened and the device is not subjected to severe mechanical deformation, then after setting the optimal frequency for powering the container, its frequency indicator will not change during use. For the capacitance design presented above, the average frequency is 310 kHz. In this case, the effective frequency range of the supply signal lies within ±10 kHz relative to the operating frequency.

Such a device has a wide electrostatic spectrum and a low gradient of plane change towards the center of the device during operation. This will allow you to effectively influence the central nervous system, eliminate circulatory disorders and many other vortex problems in the body.

Design features of a flat coil with a diameter of 12 cm

Mishin treatment coils with a reduced distance between the plates have a higher level of impact on pathogenic formations. For example, you can use a wire with a cross-section of 0.5 mm in varnish insulation. The length of each wire will be 10-12 meters.

The internal diameter will also be approximately 25 mm, and the external one - 130 mm. This capacity has a high level of efficiency. It can affect the smallest viruses, fungi, eliminate scars and accelerate the process of tissue regeneration.

Features of the torus configuration (TMA, donut)

A subsequent reduction in the cross-section of the wire and the overall size of the coil will lead to the creation of an even more effective version of the vortex capacitance. With an outer diameter of 51 mm and an inner diameter of 25 mm, a wire thickness of about 0.1 mm is created.

Such a device is difficult to make by hand. Therefore, it is recommended to use a simplified version of manufacturing the device in the form of a torus.

Making a torus

To make a torus, you will need about 15 meters of twisted pair cable (UTP 5E). The wire includes four or eight cores, which are twisted in pairs. You should remove the outer insulation of the cable and separate one pair from the rest.

To create such a container, you can use almost all types of wires. The only condition is that the distance between the wires along the entire length must be the same. Therefore, twisted pair is ideal.

Next, a piece of electric corrugation is used. It will become the basis for creating equipment for bobbin winding. The diameter of the corrugation should be 25 mm. It should be bent into a torus of the required size. A slot is made along the outside. It is secured with a couple of turns of insulating tape.

This winding will ensure the correct formation of vortices. In this case, a whole spectrum of frequencies is formed, where the internal part of the winding is responsible for high performance, and the external part for low ones.

Before you start winding, the internal lead of the wire should be threaded into a pre-prepared hole in the corrugation, and after winding, fix the outer leads. To secure the winding, it is necessary to remove the corrugation in parts. Twisted pair leads unwind, and unused ones are bitten off

Determining the device power frequency

Next, you should determine the frequency of the torus power supply. The generator terminal must be connected from different sides to the wires of the device. To determine the output voltage, the oscilloscope probes are connected directly to the generator terminals.

Then the first indicator of the frequency of the maximum voltage drop relative to the input is determined. In other words, the frequency of maximum conductivity of the capacitance should be indicated. Further nutrition will take place precisely at this indicator.

Coil power supply

The coils are powered by a sine wave (signal from the generator). Power supply via pulses is unacceptable, since it does not have inertia in this mode. The high efficiency frequency range for toroids is the same as for flat coils. It is 270-380 kHz.

During operation of the device, the supply voltage coming from the generator can drop up to ten times or more. In this case, the total power activity indicator can be no higher than 0.1 W. The maximum conducting current power should be limited to 200 mA, and the voltage to 22-24 V.

If these parameters are overestimated, this can lead to electrostatic breakdowns, which will be expressed in discharges from the center of the coil.

What generators should I use?

A frequently used generator for the Mishin coil is TGS-3. It has automated resonance tuning.

The ATTEN ATF20B+ model is considered a more professional analogue. Its advantages include the presence of a display, USB interface, frequency counter, and signal shape. Such a generator for the Mishin coil emits a signal that is not subject to distortion.

Mishina coil treatment

So, having prepared a device of the simplest configuration in the form of an inductive coil, it is possible to influence any problem areas of living organisms for therapeutic purposes. In most cases, knowledge of painful points in the body is not at all necessary, since electrostatics automatically affects painful volumetric structures and contributes to their separation.

What is vortex medicine based on? Mishin coils provide a natural application of environmental energy to influence the problems arising in the carbon form of life. This method is equivalent to the effects of antibiotics, and also serves as a replacement for operations to remove oncological tumors. The vortex flows created by the coil will easily restore the affected nerve cells.

What did the testing of the device show?

What potential does the Mishin coil have? Treatment with it gives good results. Tests that were carried out over a number of months revealed a high level of effectiveness in using electrostatic capacitance to restore lost body functions. The duration of one session, depending on the disease, ranged from 5 minutes to an hour.

Features of the treatment of certain diseases

The Mishin coil causes the release of large amounts of toxins, which must be eliminated by the kidneys through urine. Dealing with so many harmful substances when using a coil is not an easy task. Therefore, treatment begins with the lumbar region.

For a normal body cleansing regime, sessions lasting 30-40 minutes will be sufficient. They should be carried out within the first five days. The coil is applied to the lumbar and chest area. The lower back is the most important area of influence during treatment, as the kidneys are cleansed. These organs, as statistics show, are severely clogged in half of the people.

The first week of treatment contributes to significant cleansing of the body. The immune system works in enhanced mode, tissue regeneration begins.

The duration of sessions held in the second week can be increased to 60-90 minutes. This is the average. Much depends on the specific case and disease.

For example, kidney treatment should be carried out in sessions lasting half an hour. If after the procedure the patient complains of feeling unwell, weakness, chills, fever, pain, then the Mishin coil has begun its effect. If a person is able to bear the discomfort, then a similar session is carried out the next day. If you feel very bad, it is recommended to postpone treatment for two days.

Each person is able to determine what intensity of exposure he needs to be cured. The patient chooses the duration of the session individually.

At first, the coil may have little effect on obese people. Electrostatics have a certain charge that is consumed as waste products break down in the body. It promotes the destruction of looped formations. During the next session, without encountering any obstacles on its way, electrostatics penetrates even deeper and copes with the disease. Cell formation, as a rule, is located in the fat layer. This is why overweight people require a longer period of treatment. Typically, such patients do not feel any results from the sessions within the first five days.

Choosing the right mode

After the Mishin coil begins to act, you need to decide whether this mode is right for you, whether it is worth adding exposure time or whether it should be reduced. If you are on vacation, you can resort to daily long-term procedures. This way you can cleanse your body in the shortest possible time. It can also be used in shorter sessions. This intensity is applicable to people who do not have any severe acute illnesses that require urgent treatment.

A local disease, for example, pain in the knees or migraine, can be treated with another device - a torus. This bagel has a targeted effect and is perfect for these purposes. The impact diameter of the device is approximately 10 cm.

Features of the coil

There are nuances in the operation of the coil that are difficult to explain.

For example, the coil continues to work even when turned off. Only the indicator of its functionality in this case is 20%. In addition, the impact extends not only to the person to whose body the coil is attached, but also to people who are at a distance of 3-7 meters from it.

Many people are interested in how long a device such as a Mishin coil can be used. Treatment should be stopped after the body has rid itself of all toxins, as the device no longer has any effect on the body. You can apply the coil to your body throughout the day, but it will not have any effect. This is what will indicate that you have improved your health.

The action of the Mishin coil causes the release of a significant amount of toxins, which must be eliminated by the kidneys through urine. Coping with this amount using vortex medicine is not an easy task for the kidneys, so coil treatment should begin with the lumbar region. There is the main human filter - the kidneys. Every second person has problems with their kidneys. We start by cleansing the kidneys, which must subsequently cope with cleansing the entire body.

The duration of the work session is determined by personal feelings after and during use of the coil. For example, we place the Mishin disk in the kidney area for half an hour. If after use you feel unwell, have some pain, or have a fever, then the Mishin coil has begun to work. If the discomfort is bearable, you can leave this dose for tomorrow. If you feel too bad, take a break for a day or two. For those who are overweight, the coil has a weaker effect at first. Electrostatics has a certain charge, which is consumed as waste breaks down deep in the body. She destroys looped formations on her way and exhausts herself with this. The next time, without encountering obstacles in its path, electrostatics penetrates further and copes with the next dose of the disease. Looped formations are largely located in fatty deposits. That is why overweight people need more time to get results from coil treatment. These people usually feel nothing at all for 3-5 days.

After you have felt the result from the action of the Mishin coil, you need to understand whether you can work with the coil in this mode, whether to add or reduce the exposure time. If you are on vacation, you do not need to go to work, for example, it is quite reasonable to give large doses of exposure at first and get a very quick cleansing of the body. You can also go in a more gentle mode, using small doses. This applies to people who do not have any severe or acute illnesses requiring urgent intervention.

For local diseases, such as pain in the knee, head, etc., we can act differently. The torus (donut) has a targeted effect and is remarkably adapted for these purposes. The torus acts in approximately 10 cm in diameter.

There are things in the operation of the coil that will probably seem strange and inexplicable to most. The coil operates even when turned off, but only by about 20%. In addition, the impact occurs not only on the person on whom the coil is lying, but also on those who are within a radius of 3 and even 7 meters. Therefore, if you are treating someone, in order not to get an overdose, you need to move this distance away from the patient.

When a person completely gets rid of all toxins and other nasty things, the coil stops working on him. You can sleep on a coil, sit on it even around the clock, there will be no healing effect. This is precisely an indicator that you are healthy.

This is just a short introduction to using a reel safely. For a deeper study, watch all the videos and read the material.

Questions and answers regarding the use of coils for treatment taken from the vortex medicine forums.

How safe is the coil treatment method??

It is quite safe if certain standards are followed. Even if the standards are exceeded, the danger is 10%, which is a low figure. It is better to observe safety precautions if there is a person in the same room with you.
treatment by a stranger. This does not apply to members of the same family, with the exception of children, since they have increased sensitivity to the effects. It is better to keep them away from the coils. You should be at a distance of 2-3 meters from the person undergoing treatment.

What do our coils look like on thin plans?

“They look like waves connected into a sphere. In the center of the sphere there is a space with a depth of the entire height of the sphere. The wave closest to the center of the sphere and near its exit develops the greatest force. If we consider a segment of such a wave, near the center and at the exit it will be 100% in strength, and between these two points in the middle it will be 70% in strength. Between two exits
an exchange takes place, and the disease goes away as a result of this influence. If the body is loaded with diseases, then there is not enough power to destroy them. Where the torus is placed, the work goes on more intensely. At the edges of the waves it is weaker from 10 to 30%. The image of the torus can be strengthened by imagination, this will make the waves more powerful and the disease will be easier to succumb to the action of the torus. But for this you need
have developed energy or learn to develop it in such work.

How our aura reacts to the influence of coils?

- The aura becomes larger and more holistic. She is irritated by the powerful action of the waves, open areas are closed, bridges with the lower worlds through which energy flowed are removed.

How the chakras of our body react to coils?

— The chakras rotate perfectly with them - they are like a motor for them.

What is the difference between on and off coils on thin plans??

- Both work. If comparatively, then on is 100%, and off is 20%.

Is there a qualitative difference in the reactions of children and adults to reels??

— Children quickly learn the fields of a torus (disk). For them, 2-3 times of 30 minutes of weak exposure is enough, provided that their health is not burdened by serious illnesses.

The coil emits, retracts, or both at the same time?

— It emits and draws in at the same time.

What are the differences between the operation of a torus and a disk? What is their impact area??

— Degree of identity 70%. Accordingly, the difference is 30%, and it is important. Thor heals organs. And the disk adjusts the general fields - the subtle fields of the body or the surrounding space, if work is done with it. The disc can also treat organs, but it will take longer.

The main area of influence of the torus- within a radius of 10 cm. If we take the entire space of action of the torus as 100%, then these 10 cm will account for 50% of the total amount of impact, within a radius of 1 meter - 60%, 2 meters - 80%, 3 meters -100%. This is the average data. In some individuals, the fields expand to 10 meters, and in especially rare cases to 20 meters. The more developed a person’s consciousness, the larger his biofield and the larger the radius of influence. Therefore, the impact zone will be different for everyone, but on average 2-3 meters. Also, the size of the coverage area is additionally influenced by the Earth’s field of the given location where the coil operates, increasing or decreasing the size of the influence area.
Disc impact area almost the same, except for the distribution of the degree of impact within this zone. It is more uniform compared to a torus. Within a radius of 10 cm - 20%, within a radius of 1 meter -50%, 2 meters -80%, 3 meters -100%.

Does it matter which side the torus or disk is facing the body??

Doesn't really matter except for the head. It should be applied to the head in such a way that if you look at it from above, then the winding goes counterclockwise. For plants, it is better to place it so that the top is wound clockwise

« How to properly work coils with a body? Methods of working with diseases?

— A person has three main body control centers. They are located in the head, chest and abdomen. It is necessary to awaken these centers (chakras) with a disk or torus. Then the body will do its own work. It would be correct to place the main emphasis on working with the chest (in the middle of the chest between the nipples) and the abdomen (two finger widths below the navel), alternately changing positions. The stomach is the place where life force accumulates. By customizing it, you can increase vitality and restore health faster. But it is difficult to adjust if you do not work with the chest center,
since the correct energy balance is lost if you work a lot with one center. Therefore, you should alternate between chest and stomach positions. Treatment will be carried out competently if sufficient work has been done with the chest center.
Since in this center there is the main bridge of communication with the lower world, through which energy flows. When working with coils, this bridge is completely removed. Another bridge, 2 times less powerful, is located in the head space. Adjustment of the control center in the head with coils should be done after they have been brought to 60-70%
proper functioning of the abdominal and chest centers. The treatment regimen is ideally selected individually.
The scheme can be as follows: chest 10 minutes, stomach 10, chest 20, stomach 20, chest 10, stomach 10. The maximum treatment time at one location is 1 hour. But it’s better to limit yourself to 20-30 minutes. For the head – no more than 10 minutes.
Typically, the fullness of energy and the proper functioning of these three centers in sick people ranges from 5 to 30%, in relatively healthy people (those whose illnesses are of a mildly manifested nature) - from 30 to 50%. You can also find out your data by working independently with a pendulum. The total amount of time interacting with the coils is 1-2 hours for the first day and from 2 to 5 hours per day thereafter. Sessions can be 1,2, or 3 times a day, but it is better to do 3 times a day, dividing the total time into three parts.
For those who use coils on the body for 9-10 hours, although such work kills the disease, it causes great harm to the subtle fields of the body, the elimination of which requires the body to spend about 3 days, which takes additional energy.

What is fundamental in this treatment method??

Read the instructions for using the generator and coils.

What is a Mishin coil?

The Mishin coil is an electronic device that can cure many human diseases. Its action is based on the use of electrostatics.

By placing Mishin's coils (torus and disk) on different places in our body, we are cured of many diseases.

The principle of this medical device by Mishin is the effect of an alternating electrostatic field on sore spots. Here it is called vortex medicine. This is the same electrostatic attraction that we studied in physics lessons at school, when we rubbed an ebonite stick with wool and it began to attract small objects. The same thing happens in a coil, except that the electrostatic field is created not by friction, but by electronic means. In this case, we need an alternating electrostatic field.

The effect of Mishin's disks and coils on humans has proven to be extremely healing.

The kit includes two coils. A large disk for a general effect on the body (it has a gentle effect on the body) and a small one, which is called a torus, or more often a donut (a more severe and concentrated effect). We use a bagel to treat problem areas.

When turned off, the torus and disk operate at 20%. There is a known experience with roses that stood in the same water for one month and did not fade. Behind the vase on the edge stood a switched off disk. The second case shows the effective work of the disk and torus in relieving fatigue during a long 9-hour bus ride, during which the turned off disk was placed on the stomach and the torus on the chest. After the trip, I felt cheerful, although such a trip usually caused headaches.

How to work with Mishin coils.

Since you have decided to use Mishin coils to improve your body’s health, then you must assume that you have health problems. Then follow the simplest rules.

Maintain the principle of gradual impact on the body with coils. So that the body has time to remove toxins.

Before proceeding to the main problem (disease) of the body, prepare ways to remove toxins and “dirt” that will begin to come out of you.

20-30 minutes before using the coils, drink 250-400 ml of clean water. on an empty stomach. Clean water is necessary to flush out toxins and salts from the body, which will be “liquefied” under the influence of the coils. Tea, coffee, juices are not a substitute for clean water. After all, it is known that you cannot wash your hands with tea, coffee, or juice. Only clean water.

Remove all metal objects from yourself. The presence of metal staples after operations does not interfere or harm. Persons with a pacemaker can work the coil on the chest center (5-10 minutes), but make sure that there is no discomfort. It is best to use coils between meals. 1 - 1.5 hours after meals and 1 hour before meals

The coils should be placed flat to the body, on either side, because The coils act two-way. The torus is used to treat organs; the disc can also be used to treat the body; the torus has more concentrated waves in its center, while the disc has more evenly distributed waves. It is advisable to turn on the disk at a distance of 2 meters from the patient in addition to the main time of treatment with the torus, for an additional 2-3 hours a day. For example, between breaks in Thor treatment. Or leave it overnight at a distance of 2 meters.

It is recommended to start using the coil (torus) in the lumbar and kidney areas. The action of the Mishin coil causes the release of a significant amount of toxins, which must be eliminated by the kidneys. Coping with this amount using vortex medicine is not an easy task for the kidneys, so coil treatment should begin with the lumbar region. There is the main human filter - the kidneys. Every second person has problems with their kidneys. We start by cleansing the kidneys, which must subsequently cope with cleansing the entire body.

5 minutes per kidney, per day. After three days of use, take a break. 2 -3 days. This is necessary so that the body has time to cleanse itself of toxins. Then add the effect on the centers of the vascular systems (circulatory and lymphatic) - this is under the knees and under the armpits. 5 minutes each. At the same time, the blood improves, oxygen is better tolerated, and blood supply improves. The quality of blood and lymph improves.

If you have specific kidney diseases, then be sure to start using coils in the kidney area. But you can't overdo it.

If something hurts.

Place the coil on the sore spot. Monitor your feelings. If pain occurs, move the coil to another part of the body. Treatment time in one place is 20-30 minutes, maximum time is 1 hour. For the head - no more than 10 minutes, but it is permissible to keep it for headaches for up to 20 minutes if there is no discomfort. You should not spend an excessively long time on your head; first, work with the energy centers of the chest and abdomen alternately. This is a mandatory and important step in treatment. It is better to alternate, place a flat coil or torus on the chakras of the chest, abdomen, then on the diseased organ and repeat again.

The total amount of interaction time with the coils is 15 – 25 minutes for the first three days and from 1.5 to 5 hours per day thereafter. Sessions can be 1; 2 or 3 times a day. Choose the duration of treatment in days according to how you feel. If cleaning (removal of toxins) is active, stop using the coils for 3-7 days.

Symptoms of body cleansing.

Cleaning symptoms should not be frightened, but rather welcomed. Because disease and all sorts of decay products come out of the body. A well-known proverb says that there is no healing without exacerbation.

Symptoms of body cleansing:

chills, cold, warmth, drowsiness, pulsation in the body, metallic taste in the mouth, congestion in the throat, cough, phlegm, sneezing, hiccups, scratching, red rashes on the skin, numbness of the limbs, short-term heartburn, abdominal cramps, dark and cloudy urine color with a bad odor. One case of the observed symptoms of heart disease is tingling or aching pain in the heart area, pressure surges, numbness in a part of the body that could become paralyzed in the future due to a possible stroke, temporary loss of coordination, speech impairment (“stuttering” tongue), dizziness . After a week of this condition, the patient returned to normal and got rid of problems with cardiac activity. During the manifestation of such pronounced symptoms, the effect of the coils should be reduced in time to 1 hour a day, or they should be placed every other day.

Treatment options may be as follows:

Kidneys 10 minutes, chest 10 minutes, stomach 10, chest 20, stomach 20, chest 10, stomach 10.

Kidneys 10 minutes, belly 20, chest 10, belly 30, chest 20, belly 20. Chest 30.

Kidneys 10 minutes, knees 10 minutes, armpits 10 minutes, liver 10 minutes, stomach 10 minutes.

Kidneys for 10 minutes, sacrum 15-30 minutes. (if you have problems with bowel movements), lower abdomen for 15 minutes.

The location of the chest center is in the middle of the chest between the nipples.

The location of the center of the abdomen is two finger widths below the navel.

You should start using coils from the kidneys. Because Kidneys are the main filter of the body and, as a rule, they all have deposits that must be removed first.

An additional reel is already on sale. It consists of two parts. The actual flat coil (Referred to as “static” or “static”) and a torus transformer (matching element for the operation of the static coil). This coil cannot be used. Because it is very sensitive to environmental changes and changes its characteristics. But this is incorrect for her and will not have an impact. It is used at a distance of 1-2 meters from yourself. The direction of the coil should be towards itself (either side). The matching transformer has a switch "| - 0". It connects the coil to the inner winding wire or to the outer one. Both positions work. The difference is the formation of a field around the static coil. It is a ball shape or a donut shape. The time for using a static coil starts from 10 minutes. Its range of action is large. Can occupy an entire room of 12-20 sq.m. (if there is no reinforcement in the walls between the rooms, then the neighboring rooms may also be exposed to this coil)

For children: you can use the disc left on overnight at a distance of 2 meters from the child. If the disk is placed closer, the exposure time can be reduced from 4 hours to 30 minutes. Keep Thor in one location for 5 to 20 minutes, total time - from 20 minutes to 2 hours a day. Choose the time according to age, well-being and severity of illness. For pregnant women, the dose will be the same as for children.

The cost of the set (flat coil, torus (donut), generator, power supply, field indicator, instructions) is 4900 rubles.

Static coil separately - cost 1500 rubles.

For plants: experiments on plants have shown that after treatment with coils, sick plants quickly recover. But this effect is especially noticeable on seed germination. This process noticeably accelerates and the seeds receive the necessary strength for further growth and development. It is better to place the disk above the plants so that the thick part of the plywood lining is on top. Treatment once a day for 1 hour is sufficient.

For water: you can charge water in a glass container by placing a disc on top or bottom for 10 minutes. The charge in water remains for 3 hours. This treatment purifies and charges the water. Drink charged or spring water 1 to 2 liters per day during treatment. It is important to cleanse the body by taking enough fluids.

And another very important point!

This device is very helpful in healing the body. But in addition, it is recommended to bring the internal organs into complete order with the help of (previously in Rus' it was called “abdominal correction”). The procedure restores blood microcirculation in the organs. In those places where, due to violation ofDuring circulation, swelling appears and pain appears, which can be diagnosed by applying gentle pressure.

Eliminates these problems. After all, there should be no pain anywhere in the stomach when pressed. For example, the most common painful place is the solar plexus. When you press there at an angle of 45 degrees upward, you feel pain that should not be there. This pain indicates toxins in the liver and spasm of the diaphragm, poor functioning of the “gatekeeper” (the valve between the stomach and intestines). By usingvisceral therapyYou can recover problems such as:

diseases of the gallbladder (cholecystitis), pancreas (pancreatitis), liver (cholangitis), kidneys (pyelonephritis);

cirrhosis of the liver;

diseases of the musculoskeletal system (scoliosis, osteochondrosis, arthritis, arthrosis, coxarthrosis);

constipation, hemorrhoids, stomach and duodenal ulcers, gastritis;

prostatitis, impotence, gynecological diseases;

prolapse of internal organs;

vegetative-vascular dystonia;

migraine, cerebrovascular accident;

initial stage of varicose veins, etc.;

restoration of blood circulation in the pelvic organs (resumption of childbearing function);

restoration of the normal state of the mammary glands (getting rid of fibro- and cystic mastopathy).

Other chronic abnormalities in the functioning of the body.

All problems can be solved without the use of drugs. Herbs are used if necessary.

In St. Petersburg you can make an appointment online

Consultation

Here you will receive additional information about the causes of abnormalities in your body’s functions, as well as recovery methods.

Technical assistance on the use and application of reels in Skype chat:

https://join.skype.com/hR4HSuur4m2D

WhatsApp +7 911 717 7922

Or through the feedback form on the website.

Products webpage

- A strange remedy from the category of vortex medicine

Advantages: many positive reviews

Disadvantages: price

What is it like?

This is an electronic device that, according to doctors, can heal various human diseases.

Moreover, he himself selects problem areas and begins to treat them, i.e., as it were, the most dangerous place in the human body. Therefore, it is not even necessary to apply it, as doctors say.

The kit includes a generator with a field indicator, a power supply for connecting to the network, a flat coil with copper wire, a donut (torus), and instructions for use. All this pleasure cost me 5,600 rubles. I ordered online.

This entire design was developed by specialist Alexander Mishin. The coil operates at a frequency of 285 kHz, and the waveform is sine. In general, this doesn’t tell me anything, so I turned to the doctors, who explained everything in detail about the benefits of this unit.

According to them, this device can act on any problem areas in a living organism. Moreover, this may not necessarily be a person. Experiments were also carried out on animals and there, too, excellent rates of healing from their diseases were obtained.

As they say, a vortex flow of energy is used here. It acts on your problem and in some ways its effect can be compared with the use of antibiotics, which, as we know, can cause harm to some organs, but this remedy supposedly has no such contraindications.

Moreover, with the help of this device it is possible to treat various oncological diseases without surgery. There will be no need for radiation therapy. After all, vortex rays also work here, but they are not as dangerous as the generally accepted methods of fighting cancer.

Among other things, these vortex flows are capable of restoring damaged nerve cells. After all, we all know that they cannot be restored, but with the help of this unit we can try to restore it.

Doctors advise using this remedy in doses. Do not use it for too long and do not apply it to the body. 5 minutes to 1 hour is enough. And this way you can conduct sessions every day.

It is quite lightweight and easy to use.

Doctors recommend starting treatment from the lumbar region, since this coil is capable of removing many toxins from the body, which means your kidneys will do this. This means it needs to be applied to the kidneys. That is, first rid the body of toxic compounds, and then begin to further improve your health.

Of course, it all depends on the person’s obesity. If you are fat, then it will not work on you so quickly, so you need to keep it longer, but a thin person can do less. But you yourself will feel in your body how long you need to keep it in order to have an effect.

Then you can work on your limbs if your arms or legs hurt. It should be applied to problem areas. For these places, not a coil, but a torus will be used. It is convenient to hold it there and it will cover the entire desired surface.

Many people try to construct such coils and tori themselves. But still doctors do not recommend this. After all, there are many nuances in this process. If you are not well versed in vortex medicine, then you can only harm your body.

On YouTube you can find many ways of craftsmen who make them, but this should still be done by specialists with the necessary education.

On the Internet you can find many reviews about the positive effects of this coil on your body. I have just acquired this pleasure, so I haven’t noticed anything positive in my body yet, but perhaps it just takes time.

In any case, all the people whose opinions I have heard praise this miracle. If it doesn't help, at least it won't harm.

Before use, be sure to consult a specialist